Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Development board: nRF54L15DK i I'm already using "Find My Example" to connect to the "Find My" app on my iPhone. At the same time, I also want to connect to nRF Connect....
Hi,
there is my project rom size in memory report , I would like to asking what is the "NO Paths" item and hidden item
they hold my 20% ROM size. and what is the content...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hello,
I am trying to modify peripheral_hids_keyboard 's security configuration as Security Mode 1 Level 2.
According to some Q&A thread, I tried the following:
1...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
hi support team,
may i ask how to set static ip address for 7002?
1. i set these configs:
CONFIG_NET_CONFIG_SETTINGS =y
CONFIG_NET_CONFIG_NEED_IPV4 =y
CONFIG_NET_DHCPV4...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
