Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi, I am looking for your simplest product that supports this use case: When bluetooth is paired with a device, and music is NOT playing after a certain time, I want to be...
Using the SDK11 bootloader, if I recompile the bootloader, package it with nrfutil 0.5.3, and perform a DFU update the original bootloader is erased but the new bootloader...
Hello,the SDk is nRF5_SDK_15.0.0_a53641a,the MCU is 52840.
I want to memory map it and refresh it .
that's 240x320 x bytes per pixel, it's 16-bit RGB, so 240x320x2 = 150k...
A manufacturer of nrf52832 module has replaced by mistake the values of C1.C2 capacitors that are connected to the 32Mhz oscillator from 12pf to 24pf and 27pf.
What will...
Hi,
I'm using NRF52 and used inbuilt UART for communication with host controller.now i need one more uart port for log printing.
so how we can achieve on NRF52?
Thanks...
Hi Nordic team,
I'm trying to run demo SPI programs from NRF5 SDK. I want to create simple SPI communication between two dongles, of which one would be master and the other...
Hi, this is my first post here, so please forgive if category/description is not complete.
I'm trying to do a quick proof of concept using ZB ZCL Tunneling. ZED is a client...
Good morning,
I'm developing an app for NRF52832 SDK 15.3, SD 132 6.1.1 with NUS service. Moreover my app has DFU and Peer Manager with LESC JustWorks security and other...
Hello All,
I am working on an indoor positioning project where I want to send/POST request RSSI values to the server/frontend. So is it possible to send RSSI values to the...
Hello,
we have a problem with a BLE connection state function. We are working with an NRF52832 device and SDK 14. The device itself works in central and peripharel mode...
Thanks in advance for any advice!
We are developing an ultra low powered network. There will be a remote control with numerous buttons. This will connect to 2-10 peripheral...
hai , I would like to program cli uart in pca10059, what are all things to change in openthread stack in order to change UART pin configure and how to compile it ? I use only...
I am trying to implement cli uart in custom board, for which there comes need for me to recompile openthread stack (in order to change UART and LED pin configuration) in GCC...
I was just working with the ble_app_uart example in nrf5_SDK_12.2.0. Minor modification were done to the main function. The build output:
linking...
._build\nrf52832_xxaa...
