I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hello,
nRF52840 is having the inbulit RTC for keeping the time.
Should i need to use external RTC with coin battery for even after power off the BLE nRF52840.
PLease...
Hi!
We're considering implementing some security measurements into our devices, and so naturally we've started to investigate CryptoCell and other Backends supported by...
Hello,
I recently updated nRF Connect to version 3.4.0 (Bluetooth Low Energy). I'm observing, that the tool is not able to reconnect to a peripheral that was previous bonded...
Hi Nordic Experts,
I use nRF52832 for a custom board, I use GPIO P0.17 and P0.18 for controlling NMOS switch, for buzzer and vibration motor, and the frequency is controlled...
So I seem to be having trouble interfacing with nrfl2401. To initially test the chip, I sent `0xFF` to be able to read off the status register but when I do, I get `0x1C`...
Hello Nordic Team,
We are working on a BLE project with RSL10 board from OnSemi. We need a BLE sniffer to capture and analyze the BLE packets in the air for debugging purposes...
I have a module LAIRD BL651 based on nRF52810 SoC
I’m using the latest nRF5_SDK_16.0.0
I can flash ...\examples\ble_peripheral\ble_app_uart\hex\ble_app_uart_pca10040e_s112...
By taking CLI as reference: added end point handlers, changed flash placement file with zb_ep_handlers.
Issue facing was:
ZB_ZCL_CMD_REPORT_ATTRIB command is not at all...
Hi,
I have nrf52840 with softdevice and i want to write 12 byte of data at a time in internal flash,suppose i write 50 records and i have to also read it these data from...
Hi.
I am familiar with Nordic NRF51 and NRF52 as I developed OpenSource firmware for chinese ebike displays with them and using the provided examples for UART Bluetooth...
Hi,
I am trying to understand the different PHY modes available in nrf52840. What are the differences between nRF 1Mbit and 2Mbit proprietary modes when compared to BLE...
Hi,
I use nRF51822 powered by CR2032 battery. Same decoupling as dev board PCA10001.
Would you recommend different values of decoupling capacitors for battery powered...
I have SPIM working at 8MHz on nRF5340-PDK
I want to increase the SPIM speed to 16MHz.
The errata for nRF5340 states "In 128 MHz mode, SPIM max receive frequency is 16...
Hi Team,
We are using nrf9160-DK. We have tested assert tracker application, where we got the real time GPS data(DK location) we are happy with that. We also tested the...
