Hi,
I am currently building software on NRF 52810 and softdevice version is s112 7.0.1. I have one service which has three characteristics. When I add either a new service...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Dear Nordic Support Team,
We are currently exploring the use and potential benefits of the paEventCounter as described in the Bluetooth Core Specification 5.4, Section 4...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
OK, a bit of confusion somebody can clear up for me, I hope;
Does NRF_SERIAL_EVENT_RX_DATA get sent when there is ANY data in the RX buffer, or only when the RX buffer is...
Hello
I am developing peripheral interfaces on nrf9160 dk, For I2C, sPI and ADC I am not able find exapmle codes. ALso could not find api required for the same to develop...
Dear nordic:
I am working on a tool which can collect data from multiple ant+ sensors with different device types,like a bike computer.
It allows user to assign up to...
I want to communicate with two nRF52 devices without pairing?
It is possible? Yes means kindly give the realtive examples.
Maximum data length...
Thanks.
Hello there, I need to ask if these two; NRF M 24L01+1712AB , NRF M 24L01+1609AH (one with external Antenna) are still supported and have official libraries , and if not supported...
I'm trying to advertise on the coded phy, but SDK 16 seems to have a block in place against doing this when you use S340. I can obviously edit this, but I don't normally edit...
After Installing JLink 6.62 it offered a firmware update for the connected JLink. I performed the update (Firmware: J-Link OB-SAM3U128-V2-NordicSemi compiled Jan 21 2020 17...
Hello,
I´m trying to connect the nRF9160-DK to the nRF cloud, using the asset tracker application. I was able to build and flash the application. But the DK can not connect...
Hello,
We are working through an issue which we found recently on the nrf sdk. The following is what is occuring:
We have two GPIO interrupts configured for low accuracy...
Hi... folks .. i am using nRF52840 development kit , i need to control the two servo motor using ble commands . I need to control the angle and speed of two motors , suggest...
Hello,
When I power our customer-designed nRF52832-based electronics I see the ingoing suply current (at 3.1V) rising in about 3 seconds up to 55 mA (!), then decreasing...
Hi, I have a problem with uart disable function (app_uart_close();). I started from ble_app_uart example, and I want to disable uart when nobody is connected to the Ble device...
Hi,
I have a similar problem to the case: ( devzone.nordicsemi.com/.../having-a-problem-with-preprocessor-options) with not being able to access the preprocessor options...
Hi,
As per the workaround of these errata its mentioned that "This code is already present in the latest sytem_nrf52.c file."
What does the latest mean here? Is there...
