It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
I try to create coap server project and it should by updateable by DFU. I merge project simple coap server and thread dfu client, and I keep instructions in documentation...
Hello Everyone,
I am Using Nrf51822 module and s130_nrf51_2.0.1_softdevice . my actual function nrf51822 twi interface with stc3115 Gas gauge IC .read the battery voltage...
Hello,
I am implementing ble advertising using below code, i encountered a strange behaviour with this code. If jlink is connected the advertising works just fine. if I...
I have created one characteristic in which i am trying to write multiple bytes at the same time i want to use that for further processing, how to access that whole data which...
Hi,
I just started working with Nordic nRF52840 serial interfaces,can you please tell me which one is best for serial communication among SPI and I2c and why?And can you...
Hi Nordics, I know it has been asked over and over again about doing DFU of slave nrf52 using a central nrf52. devzone.nordicsemi.com/.../ota-dfu-application-firmware-by-ble...
Hi we are trying to program code using the SDK v12.3 library onto a custom NRF51822 board using SES. The custom code contains B luetooth routines, GPIO routines, and TWI routines...
PlatformIO team is pleased to announce the release of Nordic nRF51/52 development platform . This release introduces many new features and performance improvements. The notable...
Hi all,
I am trying to deploy the long range mode with nRF52840. I modified the blinky example under SK 16.0.0 and it just keeps resetting
and the error code is 0x0007...
I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
Please help me sort out one question.
I have a peripheral device that stores an archive with data. At a certain point, the archive is transferred to the central device...
Hello,
We are focussing on the nRF9160 to build a IOT datalogger.
We would like to intergrate an micro SD card.
Now, I mis the 4-bit SPI interface ( SDIO), and I asked...
Greetings,
A very bizarre thing is happening. This is the umpteenth time I'm working on a peripheral driver and the code gets stuck at 'NVIC_EnableIRQ(UARTE0_UART0_IRQn...
I would like to implement Bluetooth 5 packet exchange without the softdevice.
How can we convert the
nRF5_SDK\examples\peripheral\radio\receiver
nRF5_SDK\examples\peripheral...
How can you use assisted GPS(AGPS) in nRF9160?
Let's say you get assisted data from "supl.google.com" and how do you set this address in code?
Do you have to wait for...