I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi everyone,
I was looking at the SAADC example and I need to modify it in order to fit my design. I want to perform analog readings from eight sensors using an eight-channel...
Hi,
I'm developing a BLE application that is also using FreeRTOS.
I also need to use PWM to control an LED (mainly because the requirements define LED patterns, which...
Base BLE structure ble_advertising_t contains a member structure ble_adv_mode_config_t. This structure contains two parameters that are meant to limit number of advertisements...
Hi Team,
I want to create on flash section to store the specific data like Crypto Keys and Serial numbers. How to create one page/section in existing Flash memory without...
I am trying to test a BME280 sensor on the nRF9160. I followed the steps where I created a folder (board) and added the nrf9160_pca10090.overlay and add couple of line in...
Hi, I would like to implement free rtos on nrf 51 using IDE Segger Embedded Studios. Could some one please direct me to the necessary links/ information.
I have researched...
Hi ,
I am working on project which is based on nrf9160 Development board.
could you please verify these points-
1. I am sharing the snapshot of the registers...
I have downloaded the Keil compiler and the Nordic key for same.
When running Keil_v5/UV4/PackInstaller.exe I can not get the update:
Cannot download file developer.nordicsemi...
Good Day,
i´m want to use saadc with 7 channels. I´m using the ADC Driver with an interupt handler. All 10ms the sampling starts per cpu. I use the configuration followed...
Hello,
I am running on a NRF52840 DK a Zigbee program configured as a router. For the coordinator i am using the cli example from the SDK.
On the router, I have developed...
Dear Nordic Semi, ladies and gentlemen!
I'm working on a prototype device with USB host functionality. I am using Arduino USB Host Shield connected to nRF52840 DK . DK is...
Hi，
We want to confirm the effect of GPS fix_interval and fix_retry, so we start GPS with parameter fix_interval=10s, and fix_retry=30s, then get the result as the following...
I try to bonding.
Using SDK 15.3. 0 and S332 Softdevice.
I successed bonding procedure used Peer manager.
after bonding, If I try to connect one more, nRF Connect app...
Hi, I can not connect to nRF52833 and nRF51 after I return from Flight mode on Android devices. I am keep getting Error 133 (0x85): GATT ERROR. I am using the nRF Connect...
