I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
I would like to use the UART at the lowest possible level and Ihave created a very simple example which uses the UART bus with the registers. The example should write word...
Radio is flashing green, on and off, but I can't seem to connect to it. Looking at the graph of usage, I can see that it is talking to something since the available amount...
Hi,
I'm using pc-ble-driver-py.
I bought the nrf52832 dongle.
The problem is uart pin number of dongle.
The pins of my dongle and the pins of the hex file are different...
I am working on adding firmware updates to my BLE application on the BL652 module ( nRF52832/PCA10040 ). nRF 15.2.
I added in the code for the BLE Background DFU, which...
Hi ,
I can not understand or there is something wrong in this example here ;
He defined " point_fifo" but initialized "my_fifo" , How does this work ?
https://infocenter...
We want to qualify a product with nrf52832 and preferable S132 6.1.1. When we tried to use QDID 125047 there were inconsistency problems in Launch Studio, table 1a was not...
Can i configure more than one pin for wake up the microcontroler from deep sleep ? like this: nrf_gpio_cfg_sense_input(30, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_LOW); nrf_gpio_cfg_sense_input...
What is the receive buffer size for IP packet data, i.e. how many bytes of data can the modem receive (in one or several UDP packets) before I call recv() or recvfrom() on...
Hi Sir,
For test the nRF9160 GPS, based on the nRF connect v1.2.0.
Do we have the GPS API for cold/warm/hot start?
And which example code we can reference?
Thank you...
Hi,
Recently I have been working on serial LTE modem code and it seems to work great for TCP and UDP. I am trying to enable GPS module by the command mentioned in this link...
Hi,
is the 100k pull-down on the COEX2 pin required as stated in the product specification ? I don't see it being followed anywhere (reference circuitry, nRF9160 DK schematic...
Hi,
I am developing nrf52832 on zephyr platform, I have seen a very useful GitHub library you guys have created called 'NordicPlayground' https://github.com/NordicPlayground...
How can I log on a router when a coordinator is in pairing mode, what I mean is that the coordinator sends a message so the routers know and set them selfs up on pairing mode...
For our nRF52832-QFAA design, we've just completed all tests according EN 300 328 (Radio). All but one test passed: spurious emissions at 4.9 GHz showed -44dBm, exceeding...
I use nRF52832 chip and SDK 15.3 version. I try to build nRF52 project with SDK 15.3.0. I spent a lot of time to fix a lot of issue in during compilation and linking. I used...
