I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
If I write the data from NrfConnect App and if I again go to the scanner tab without clicking on disconnect or killing the app and then if I click scan or refresh option,...
I want to transfer files to uart using ymodem protcol.
For example, when nRF52840 receives a file through BLE,
it tries to send the file back to the device connected to...
Is there a sure fire way to know for sure that my PSM configuration is correct on the nrf9160DK? I'm trying to get LTE-M + GPS working and I'm still not sure if I'm in PSM...
Hello,
We used the Nrf52810 in our project.
Currently, we found a issue: The ble is disconnected when we press the chip. Because our buttons are on top of the chip. We...
When I use circuit configuration no.5, VDD connected to VDDH and have 5V going into VBUS, I see a 1.6V output from the VDD_nRF (VDD/VDDH).
Normally when I connect a battery...
This question is a follow on to https://devzone.nordicsemi.com/f/nordic-q-a/38085/how-to-create-a-copy-of-examples-project---segger-embedded-studio .
It's clear that making...
Hi,
Can i use nRF52840 Pre Development kit as a sniffer.
Also can i use it to program my customized PCB
Note: I need to do both of above urgently so i cannot wait to...
nrf connect sdk version :1.2.0
application:nrf_: desktop
I use command " west build -b nrf52840_pca20041 -d build_pca20041" , but it report error at last.
I don't know...
Hello
Currently, there are systems that operate with peripherals developed with nRF52832, SDK v.12.2.0. I have a question about supporting this for meshes.
1. Are you...
Hello,
I am trying to send a rather large HTTP payload from the nRF9160, the payload is about 10KB in size. The problem I am running into is that after about ~4KB of data...
I'm actually building a project that need to communicate with sdcard.
i read a lot about that and i'm very confusing when i passed on nordic sdk lot of code and ressources...
Hi all,
I am working on a project which uses a vibration motor. I want the vibration motor to vibrate with different patterns. I have read online that a 20kHz PWM can be...
Hi,
I've found this answer which states that the NUS throughput is around 2-4 kB/sec.
https://devzone.nordicsemi.com/f/nordic-q-a/27044/ble_uart-demo-throughput-is-very...
Hello guys
I am trying to compile the latest nrf sdk with version v1.2.0 it fails with the following error
but when i compile either v1.0.0 or v1.1.0 it is successfully...
