I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi Team,
We are working with nRF9160.
Below are my queries:
1. Can we use same voltage for VDD and VGPIO? If so, how can we control the VGPIO?
2. What would be the...
Hi,
I am working on a hub based on a raspberry compute module. Zigbee support is enabled by a u-blox (or Rigado) BMD340 module connected via UART to the compute module....
I have uploaded nordic thingy 91 with lte_ble_gateway program and modified it so that it can connect with 7 devices, however when i try to connect the 6th device I get bluetooth...
Hi,
SW8 (MKH-22D14-G2-B) on my board is mechanically loose. When it is in on position, the board will intermittently power off and then back on. I did not find supply online...
Hi Guys
So I am new to this whole LWM2M protocol, so my knowledge is not that good. I have the following problem. I want to start the LWM2M_client sample with the following...
In the existing nRF5x SDK, there is a type 2 and a type 4 NFC library which can be used on nRF52 chipsets. With the introduction of zephyr and the new dual-core chipset based...
Hi,
Here's my setup:
Custom board built with nRF52840
nRF5_SDK_for_Thread_and_Zigbee_v4
Segger Embedded Studio for ARM v3.52
I have built a Zigbee Coordinator...
Hi!
About my application:
SDK 16.0.0.
FreeRTOS and SoftDevice s140.
Peripheral role (buttonless dfu without bonding)
Central role NUS_C
When incoming connection...
Hi,
If I edit a project config file (.conf) how do I get SES to rebuild the project makefiles via west?
The only way I've found is to reload the project. Which seems a...
Hi teams,
Recently, I made a custom board based on nRF52833 DK.
It works fine until now, and most of things works well.
But, I cannot make the board to show logs in...
I can see advertising packets of a device using an nRF51822 in Wireshark (example packet capture here https://imgur.com/a/maV6kbb) . But can't see them in nRF Connect on Android...
Hello,
I'm using the peer_manager in a GATT server project, after a first bond was created, I want the peripheral (GATT server) to advertise with ADV_DIRECT_IND, once the...
Hi,
I started development of nRF51822 with Keil(V6) / nRFgo / Segger etc..
I got SDK and exxample from here ( https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v6.x...
Hi ,
I use the C language and pc-ble-driver to development a PC tool. Now I can use handle to establish connection. How can I use the pc-ble-driver update the target device...
