hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I am developing a PC SW that connects to nRF52840 device throw a BLE USB dongle(another nRF52840)
How I can tell from PC that a device is connected\disconnected...
Hi,
I use nRF9160 custom board and my application uses USART, ADC, I2c, SPI, RTC and LTE modem. Currently I am trying to reduce sleep current on IDLE state which is 850...
I am going to use nRF52833 chip with SDK v16.0.0 and SoftDevice s140.
There are couple of questions I would like to clarify:
1. Is AoA/AoD direction finding supported...
Hi
Using the nrf52840-dk with SD S140 and nrfx_gpiote, everything runs fund (BLE, TWI etc) but interrup on pin 0,28 causes a Hard Fault. I can not get any sensible logs...
I am trying to modify the existing Thingy-52 code to have a 'new' characteristic. I used the existing Thingy code to 'clone' a new characteristic (a 2nd microphone channel...
Hi
We tested the idle feature(by AT#XSLEEP=0) on nRF9160DK, but no significant change of power consumption before and after enter into IDLE mode, is this result correct...
Hello, I would like to save a log in the nrf5340 FLASH, how many times is possible to write? May I write in the Application CPU Flash from the Network CPU FLASH when the Application...
Hello
I am trying to discover the correct scan interval/window settings to capture the advertized packets from a beacon transmitting every 100ms(10Hz).
Should I just set...
Hello! I've have been designing a custom board. The circuit reads ADC channel 1 for long periods, 1 hour at most. When the reading is high enough it will send an alert using...
Hello,
I am trying to build a remote control using NRF52832 SoC, SDK16.0.0 with softdevice S132 version 7, Keil 5.
I have to control a servo motor and i want to achieve...
Hello,
I need to send logged sensor data in external 4MB flash to a phone via BLE.
I am using a nRF52840 based module on a custom PCB. I am using SDK v14.2.
I am using...
Hello,
Is it possible to get access to the information contained on the SIB (System Information Block) in the nrf9160? if yes, is it through the nRF Connect v3.3.0?
Thanks...
I want to get the 128 characteristic UUID of the peer device during the connection phase. Now I use SDK is 15.3, the softdevice is 6.1, and only 16-bit UUIDs are obtained...
I have the NRF52 DK, I run make flash in the UART example, everything works. I'm able to run the loopback test.
I navigate to the serial port example, make flash, nothing...
