Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
I'm working on an nRF52832 based IOT product using Segger Embedded Studio for ARM v4.50 on my Windows 10 machine. My project uses FreeRTOS. Looking at the release notes for...
Hello,
This may be normal behavior once correct connection management code is in place, but I want to verify since originally I was looking at 2-3 minute connection times...
I want to use a comparator without interrupt.
The measurement is not time critical.
Therefore, I chose the LPCOMP.
For initialization I use the following code:
For...
Hi Team,
We are working with nRF9160.
Below are my queries:
1. Can we use same voltage for VDD and VGPIO? If so, how can we control the VGPIO?
2. What would be the...
Hi,
I am working on a hub based on a raspberry compute module. Zigbee support is enabled by a u-blox (or Rigado) BMD340 module connected via UART to the compute module....
I have uploaded nordic thingy 91 with lte_ble_gateway program and modified it so that it can connect with 7 devices, however when i try to connect the 6th device I get bluetooth...
Hi,
SW8 (MKH-22D14-G2-B) on my board is mechanically loose. When it is in on position, the board will intermittently power off and then back on. I did not find supply online...
Hi Guys
So I am new to this whole LWM2M protocol, so my knowledge is not that good. I have the following problem. I want to start the LWM2M_client sample with the following...
In the existing nRF5x SDK, there is a type 2 and a type 4 NFC library which can be used on nRF52 chipsets. With the introduction of zephyr and the new dual-core chipset based...
Hi,
Here's my setup:
Custom board built with nRF52840
nRF5_SDK_for_Thread_and_Zigbee_v4
Segger Embedded Studio for ARM v3.52
I have built a Zigbee Coordinator...
Hi!
About my application:
SDK 16.0.0.
FreeRTOS and SoftDevice s140.
Peripheral role (buttonless dfu without bonding)
Central role NUS_C
When incoming connection...
Hi,
If I edit a project config file (.conf) how do I get SES to rebuild the project makefiles via west?
The only way I've found is to reload the project. Which seems a...
Hi teams,
Recently, I made a custom board based on nRF52833 DK.
It works fine until now, and most of things works well.
But, I cannot make the board to show logs in...
I can see advertising packets of a device using an nRF51822 in Wireshark (example packet capture here https://imgur.com/a/maV6kbb) . But can't see them in nRF Connect on Android...
