Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
We have a custom board based on the nrf52, We trying to integrate BLE functionality into our already existing firmware. I am able to create a custom service and characteristic...
ret is declared inside a "CRITICAL_REGION" which is a block, so not accessible outside that block to return: ret_code_t app_usbd_hid_generic_idle_report_set(app_usbd_hid_generic_t...
Hello, trying to make the leeap from nRFGo studio to nRFConnect, programming tool. I have connected to an old device programmed with nRFGo, and see the memory map below. I...
I am trying to debug an app error in my code. I have an app_error_fault_handler that starts like this:
But, the "Fatal Error in file..." line doesn't show the file...
DFU over serial
- Application alone - works
- Softdevice + bootloader works, but then doesn't respond to ping when trying to send Application image next
nRF52832 ...
Hello,
If the locators have AoA direction finding support ( nRF52833, nRF52833, nRF52820 etc , ) does beacon device require to have direction finding capabilities as well...
hello ,
I am using NRF52840 for my application, ESP32 as central and my nrf52840 as a peripheral . central always connected with peripheral. i can send data through central...
To the kind attention of Nordic support team,
I have been reading https://infocenter.nordicsemi.com/pdf/nRF52833_PS_v1.0.pdf product specification, where only
aQFN 73...
Hello everyone, I wan't to layout my own PCB board of nrf52840 ,is there any things need to be attention? By the way, if I'm not using Interface IMU to upload my programming...
When I have put the nRF9160 modem into mode 4 or 44, and then issue a status read AT+CFUN? command, the modem erroneously goes online. I have used latest and greatest modem...
I have the following code in my main.c file:
I also have mylib.c and mylib.h file. I want to move my function there. I tried the following.
mylib.c
mylib.h
I...
Hi, I am trying to get DFU from SDK16 working on my Mac.(Mac Os Mojave). I am following the instruction on https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16...
I have been unable to upgrade my BL652 modules to v28_10_7_0_r0 firmware using a Segger Jlink EDU (HW v10.10, DLL v670) and Windows 10 Pro. (v28_9_6_0_r0 package also fails...
Hello,
I have been trying to get the light switch server from the Mesh SDK examples running on a nrf52840 dongle. The dongle does not show in the Mesh app when scanning...
I installed SEGGER and started the program. I then applied of the free Nordic license and activated it. The problem is that whenever I close the program it asks for a new...
