How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello,
I successfully downloaded SAADC SDK example in the peripheral folder. The hardware setup is as below ,
The pin configuration for this is as below
...
I tried implementing
https://github.com/andenore/NordicSnippets/blob/master/examples/temp/main.c
But i get 2.6V without connecting any of the Analog pins.
Exactly...
I have attached an Arduino INO file that I wrote early on in a project. It runs a probe. It is an amazingly simple probe but especially important. I am making a simple opacity...
Hi Team,
I planning to use vibration motor with nrf52832.
vibration motor will give maximum buzz on 20.3KHz(50 duty cycle).
So my question is
- Can I achieve 20...
Hello I would like to use the extended advertinsing packets from Blutooth V5 as used in the "ble_app_rscs" example. My problem is that I can't connect via the extended advertinsing...
It looks like NRF_LOG_INFO doesn't copy the data that is sent to it as per the below example. Is there a way around this so that I can reuse long buffers that contain either...
Our purpose is to integrate BLE 5 in our embedded application, and do it quickly.. We basically need to send/receive data with maximum throughput.
Per thread below, we are...
I am having some issues bootloading the dwm1001 board.
I am able to flash over UART and BLE using nrfutil and nrfConnect with:
s132_nrf52_6.0.0 softdevice
pca_10040...
Im trying load a TWI sensor custom built with LIS3DH, and it is showing following error.
The xml file looks as below
Can you kindly guide me, how to resolve...
Hello. I'm trying to create a new project or open existing examples with eclipse.
I tried to import "Existing code as Makefile project" and File->New->Makefile Project with...
I would like clarification on the use of the nrfConnect programmer for RE-programming the "dongle" a.k.a PCA10059. NOTE: NOT "programming a virgin dongle" Reference: The user...
I'm having trouble with certification in China. Here is what they are getting for spectrum using the nrf52832 with the nrf_radio_test_example. The lab is saying that this...
Hi,
We need send packets continously, and need adjust TIFS slightly when real packet interval is shorter or longer than expected.
The radio shorts register is set to RADIO_SHORTS_READY_START_Msk...
I tried implementing the custom BLE example in the below link Im facing two problem 1. ble_cus.h header file throws error
Main
ble_cus.h
ble_cus.c
The error...
I have just integrated the Buttonless DFU example code into my project and I am able to successfully update my device using nRFConnect. I'm using the NRF52840, S140, and SDK...
