Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
hello everyone：
I have an issue on nrf52832 running freertos based on SDk 15.0,I am using PPI and SAADC to get 2 channels data .I find that if I change the configuration...
Hi,
I have 3 estimote beacons which I want to scan using nrF52833 and display scan response data on Segger RTT viewer and I don't want to establish the connection between...
Hello,
i've made a custom shield plugged into the thingy: 52.
There is a tag connect connector on it. I have short SWD signal from thingy debug connector.
When i try...
Hey,
Is it not possible to use any Bluetooth status codes for disconnection when calling sd_ble_gap_disconnect ?
for example this is not working (I do not actually disconnect...
Hi,
Similar as this issue
Our QA team found the nRF9160 device will hang when user pull out the USIM card then try to deactivate LTE.
The issue can be repoduced by following...
We tested this issue on serial_lte_modem sample on NCS 1.2 and modem mfw_nrf9160_1.2.0
1, Enable CSCON unsolicited report:
AT+CSCON=2
2, Activate LTE search and connect...
Hi,
My problem in shortly is when I have debugger connected to nRF5282, I always get hardfault after some time.
https://i.ibb.co/hZ3bZ1b/optionbytes-1.png
I tried...
hi .i use the pca10056 connect to th nrfconnect by usb .andr dun the app Bluetooth low energy.other 52840 device run the hex of \nordic
sdk\nRF5_SDK_16.0.0_98a08e2\examples...
Hello,
I'am working with a project and want to maximize ble throughput from ble thingy52 to a central device. I have used the ble sniffer with wireshark to see data transfer...
Hi Team,
i am working on serial LTE modem sample project trying to send at commands through serial lte link monitor, found that device is not responding to at commands...
Hi,
Recently I updated nRF Toolbox iOS to 5.0.1.
I'm mainly using this tool for writing application via DFU to nRF51822 board.
I was using .hex files for DFU but I can...
Hi,
I am working on a product based on an nRF52832 (SDK 15.3, Softdevice S112 v6.1).
For security purposes, I would like to restrict the pairing / bonding procedure to...
Hello, guys!
I am using master branch of nRF Connect SDK and want to use UART_1 module of nRF9160 SiP to communicate with external devices.
I used nrf9160_pca10090ns.overlay...
Hello, I am evaluating different printed antenna options for my Nordic design using nRF52 series ICs. The small size of the meandered antenna used in the nRF24LU1 USB dongle...
