Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hello, I am developing a Python script (Windows 10, Python 2.7.16, pc-ble-driver-py 0.12.0) to use a NRF52840 board to simulate the BLE part of an application running on a...
Hi,
I'm working on the nrf52832 development board and SDK 16.0. I want to use the Power supply supervisory functionality to detect any type of power failure.
I'm using...
Hi,
The example is currently printing the device address
on_adv_report(ble_gap_evt_adv_report_t const * p_adv_report) { ... NRF_LOG_INFO("Connecting to target %02x%02x...
I am going to find out an ideal throughput of NRF52832. And my environment is NRF52832/S332/MTU 247/connect interval 20ms.
Finally, i got a maximum value about 23Kb/s. I...
I have a nRF52840-PCA10059 dongle.
I have a PCA10040 dev boeard on which I programmed the ble_app_hrs_freertos_pca10040_s132 example after I modified HEART_RATE_MEAS_INTERVAL...
Hi,
I have some code which is based on the ble_app_gatts_c example sdk 15. I am using a Nordic NRF52840-dk pca10056 s140. Coding in Segger.
I want to each second change...
Hi,
I want to set the unused pins to low Level, however without using Software to do so, i.e. this has to be done before the chip is turned on.
How can I do that? Is...
Hello all, I have a little problem.
I`m trying to do an gateway communication using my NRF9160. The routine I`m trying to accomplish is next : -- Send message over serial...
Hi... i am getting the data through the RX,TX which is externally connected to the nRF52832 development kit , now i want to store the continous incoming data to the variable...
Hello, I am using nrf52840 board and SDK 16.0.0.
I am trying to merge this calendar example ( https://github.com/NordicPlayground/nrf5-calendar-example ) into ble_app_template...
1. I am trying to test the QSPI flash performance in nrf52840_DK ,but the QSPI init failed because of the event ready check,can i turn off the event check process?
2. I...
The recommended circuit in the v0.5 nRF5340 product spec differs a little from the nRF5340-PDK and I'm trying to understand the minimum requirements for an antenna. The spec...
Hi everyone, I am a beginner with the nRF52840 and I am looking at the example spi_pca10056 on SDK 16.0.0. What I've noticed is that at sdk_config.h file the pin configuration...
I have a question about what functionality is handled in the modem firmware vs. the application firmware.
I see from the nRF Connect SDK that the nRF9160 application communicates...
