Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello,
I'm working on adding an HTS service to an existing device (nRF52832), and running into a problem that can be reproduced on PCA10040 and S132 5.0
When my code is...
I modified the firmware of our control unit to allow BLE communication. Now It communicates with an ANDROID APP. The chip used is nRF24L01+, It send and get only Non-Connectable...
Hello,
I'm trying out the HID Keyboard example (sdk 16.0.0, s132) and was able to pair once to my phone. Now I can't pair to any device. The following pop-up window appears...
I'm running SDK 14.2 using FreeRTOS on a nrf52832.
When I increase NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 158, the system ends up in Hard Fault.
Anyone have suggestions on...
Hello,
I am using an nRF52 to transfer 20 bytes (through notifications) to a raspberry pi (with bluetooth dongle). I've been experiencing some weird connection times: I...
Hi
I have 1 PCA10040 dev kit and 1 Raspberry Pi 3.
If I connect NRF dongle to Raspberry Pi will Raspberry Pi act as mesh-node ?
All I want to do is send data from PCA10040...
Hello,
nRF52840 is having the inbulit RTC for keeping the time.
Should i need to use external RTC with coin battery for even after power off the BLE nRF52840.
PLease...
Hi!
We're considering implementing some security measurements into our devices, and so naturally we've started to investigate CryptoCell and other Backends supported by...
Hello,
I recently updated nRF Connect to version 3.4.0 (Bluetooth Low Energy). I'm observing, that the tool is not able to reconnect to a peripheral that was previous bonded...
Hi Nordic Experts,
I use nRF52832 for a custom board, I use GPIO P0.17 and P0.18 for controlling NMOS switch, for buzzer and vibration motor, and the frequency is controlled...
So I seem to be having trouble interfacing with nrfl2401. To initially test the chip, I sent `0xFF` to be able to read off the status register but when I do, I get `0x1C`...
Hello Nordic Team,
We are working on a BLE project with RSL10 board from OnSemi. We need a BLE sniffer to capture and analyze the BLE packets in the air for debugging purposes...
I have a module LAIRD BL651 based on nRF52810 SoC
I’m using the latest nRF5_SDK_16.0.0
I can flash ...\examples\ble_peripheral\ble_app_uart\hex\ble_app_uart_pca10040e_s112...
By taking CLI as reference: added end point handlers, changed flash placement file with zb_ep_handlers.
Issue facing was:
ZB_ZCL_CMD_REPORT_ATTRIB command is not at all...
