Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello,
We have seen the below error,
NRF_ERROR_INVALID_ADDR If the EasyDMA is used and memory adress in not in RAM.
While trying to connect with an external sensor hub...
Timer A with a 10-minute interval, timer B with a 4-hour interval, and timer C with a 10-second interval are required, and A and B should also run out of time in low power...
Are there any updates on coded phy support for the nRF sniffer?
I found a thread about this from "over a year ago" which says to check back in 4-5 weeks: https://devzone...
When CENTRAL connects how can I read the UUID and ADDR of the peer?
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context) {
switch (p_ble_evt->header...
Hi Team,
We are facing issue with Flash storage Handlers with ble handlers. When we add the fstorage to my application ble adversing is stopped suddenly.
We are having...
Hey,
I want to use a standard 16bit service and to add some custome characteristics to it, will this create any compliance issues? Is it complying to BLE specifications...
Hi all,
I'm using the "ble_beacon_app" example from the SDK 16.0.0 with the nRF52840 DK. I would like to change the TX power level.
In main.c function, I tried to change...
Hi All,
We tried to modify the Android source core of nRFTools for our Proximity application . And we used some nRF52832 and nRF52840 as the proximity device.
1) We connected...
Greetings,
we are developing a custom board that holds a nrf9160 chip. We have uart lines out on pins 28 and 29, as on the DK. We need to use the AT client in order to flash...
I've implemented a Application and Bootloader. I have the Bootloader set to Buttonless. However when I try to transition from the Application to Bootloader via:
/* Sets...
Nordic team:
We are developing a proprietary application for Android tablets using the Android-BLE-Library and have been experiencing issues with scanning after a long period...
Hello
I'm very new with nRF modules and currently struggling with BL652-SA-01-T/R module to run Bluetooth.
I have developed small pcb to test this module, PCB includes...
Good day,
I am using the ANNA-B112 BLE device from ublox in a custom design. The ANNA-B112 interfaces with a host MCU over UART. The ANNA=B112 is flashed with Soft Device...
Hello I have an application which requires the use of both BLE and Openthread in the same time. The BLE is meant to connect an OpenThread mesh network to a smartphone.
I...
Hi, I am trying to create a project using make in addition to my SES project. My problem is that I see no printouts on /dev/ttyACM0 (using minicom to debug this), but I do...
