Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Dear.
Now Im testing the nRF24L01 to develop a module.
Using this, I want to know the receive power.
nRF24L01 has a registef to use similar function. Register...
Hi,
I'm trying to write firmware for the nrf52840 that reads from a sensor and then sends data to a PC over BLE. Ultimately, I need the BLE link to achieve ~ 1.1 Mbps throughput...
Hi all,
I observe a connection supervision timeout (HMI error code 0x08) in my Nordic firmware with certain Android smartphones (controller).
Additional info regarding...
Hi. I'm just wondering if Nordic Semi engineers have done any tests with standard beacons (any particular beacon interval and test condition) application and compared current...
Hi teams,
We made BLE mesh custom boards based on nRF52833.
These nodes are configured to send broadcast messages for every 10 seconds.
Currently, these boards uses...
Hi Sir,
We would like to use the Radio test to do the basick TX/RX test in SDK 15.2
We use the nRF52840-DK for test and follow the CLI document .
1. We use two board...
Baud rate 460800, error code NRFX_ERROR_INTERNAL(1) occurred when the serial port received data。
I want to know how to avoid this problem, the current transfer rate is less...
Hi
We need the recv() be blocking until the full amount of requested data can be returned or the operation was timeout, how to achieve this?
I tried flag MSG_WAITALL but...
Hi. Can anyone think of a way to use the nRF52832 (probably Timer) to detect approximately 125KHz-150KHz variable square wave down to about a 1Hz resolution? I'd like to detect...
Is there any example for Directed Advertising? I'll design my NUS central and peripheral use Directed Advertising, because I would like to have other bluetooth devices connected...
I use this code below mentioned in this question https://devzone.nordicsemi.com/f/nordic-q-a/26030/how-to-reach-nrf52840-uarte-current-supply-specification
This can reduce...
Do you have any recommendations, tutorial, blog, or getting starting guide for a developer wanting to use Mesh and BLE on the same node? Any information would help. Does one...
Hi,
After long use of BLE communication I sometimes get return code 8 from sd_ble_gatts_hvx.
My questions:
1. This return code is cryptic. Is it associated with defined...
I am trying to configure the CryptoCell on an NRF52840 to use AES-CBC encryption with PKCS7 padding. When I call the following function, it returns SASI_AES_ILLEGAL_PADDING_TYPE_ERROR...
Board: nRF52833 DK
Version: 1.0.0 PCA10100
SD: s140
Env: Segger v4.52 (installed on 5/10 via Toolchain Manager)
Hello all...
I'm running into a problem with the...
