nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi all,
I am on the DK-52 with the SDK 13.0.0.
After erasing the device, I follow this steps:
upload the softdevice
nrfjprog --reset --program s132_nrf52_4...
Hi Forums,
I work 51822 custom board.
I try to add Buttonless DFU so I test the "experimental_ble_app_buttonless_dfu" compile is good.
But flash to the board can...
I am building a Bluetooth Mesh network with multiple types of devices.
The provisioner is now capable of provisioning and configuring multiple instances of Device A but i...
I am using nrf52832 with softdevice s132 v3.0.0, sdk 12.2.0 and FDS.
I am using sdk_config.h to configure various modules in my project.
Earlier config: Using Timer1...
Dear nordic devzone,
When trying to build the "ble_app_hrs_c" example project it does not build in SES.
Output/ble_app_hrs_c_pca10056_s140 Debug/Obj/peer_manager.o:...
Hi,
I'm currently investigating the Bluetooth mesh using the SDK for mesh alpha 0.10.0, I was wondering about the limitations on the re-transmission of messages. The current...
this issue might also be one of others than myself
my main development environment is based on linux ... firmware, QT, android and whatever comes along ... i used to write...
Is there native support for hardware coex lines? If we have a WiFi chip that produces a TX Active signal, can we hold transmit from the nRF52840 till that transmit is finished...
I have bought a Tayio Yuden EYSGJNZWY Bluetooth module, which is in fact just a Nordic's nRF51822 (256KB Flash and 32KB RAM) with added antenna. Tayio's files say that the...
Hi,
I have built an application which is based on BLE and protocol that supports high frequency sampling of sent messages. I tried to achive that using only BLE, but it...
Hello,
I am designing a custom board with NRF52832 IC. I have a query regarding routing of traces.
In my design, I am not using all pins of IC. Do I need to route traces...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
I'm using SDK13.0.0 ble_app_ancs_c example.
On connected with a phone, pm_evt_handler is called with PM_EVT_CONN_SEC_SUCCEEDED, and call ble_db_discovery_start(), then...
