I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I want to connect 4 antennas to nRF52832, they respectively points to North, South, East and West direction.
Also I hope the nRF52832 can do switch antenna job,...
I'm trying to use gcc and eclipse but I'm getting an error in eclipse that certain variable names cannot be resolved. I know that its not being able to get the variable names...
Hi,
I am developing a small development board of visiting card size, which is powered from a coin cell. I have two questions,
All i want know is there any polarity...
Hi,
do sd_flash_page_erase or sd_flash_write provide any guarantees that the command has executed successfully or should I do a manual check to verify if the page was really...
Hello all,
I am working on nrf52832 Board and i want to use it as translator to send and receive the data , please tel which pins i need to select as UART(rx,tx) pins ...
I am designing a custom board with nRF52840, powered by USB, no battery, using its internal LDOs to supply other peripherals with 3.3V
I have two questions about pins/outputs...
Hi
I generate a pwm signal via changing the state of one characteristic. In general, the pwm works fine. But the problem occurs when I add the timer which is responsible...
Hi guys，
I use the 51822's PWM recently, PWM is made by GPIOTE+PPI+TIMER, and the PWM source code as below(I use TIMER1, GPIOTE[0], PPI_CH[0], PPI_CH[1]， period and duty...
Hi all, I'm asking on both BLE specification version 4.0 (or more) and NRF51822 S130 about having support for multiple central connections at the same time while our NRF51822...
Hi,
I get RSSI values like -96 or -97 dBm before the coded PHY connection between two nRF52840 pdks drops. Are these values something expected? TI advertises sensitivity...
Hi, there~ Nordic's Mesh SDK is fascinating! I was thinking of a way how to connect the Internet with Nordic's Mesh devices.
From the web, you might have seen these...
Hello,
I'm working with the thread v0.10.0 sdk release and I would like to customize and add some new packages to the border router.
I see that there is a release tag...
On the BLE Secure DFU Bootloader page of the documentation, there is a typo. See ' Secude ' in the following text.
Configuration parameters
There are certain configuration...
We have certain boards having nRF51 onboard. We want to use them as sniffer. Unfortunately, pins that are used for UART on nrf51DK board are not accessible on our boards....
Dear Nordic Development community,
I have a very interesting project going on based on bluetooth speaker controls.
In short words, i'd like to control the sound level...
