Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I try to run UART/Serial Port Emulation over BLE on SDK v14.2.0 with nRF52 DK and nRF Connect on Android phone following link " http://infocenter.nordicsemi.com/index.jsp...
I am trying to run the coap ipv6 based example code provided in nRF51 IOT SDK. I am using my Linux PC along with a BLE adapter as a BLE enabled router. I can successfully...
I came across this a while ago, however it gives no indication as what releases, of Segger J-Link suite, each nordic J-Link OB download has been tested with.
Is there page...
Hello, I am looking for documentation on the Mesh DFU Protocol. It looks like it is the same DFU that the mesh branch of the nrfutil python app is using. I would like to do...
Hi,
I tried to use fs_erase and fs_store functions but they both return the value FS_ERR_INVALID_CFG which means "Invalid fstorage configuration". I'm working on nrf51822...
Hi,
I'm using SDK 14. I started from ble_uart application, and to use ADC as well I ported ble_app_uart__saadc_timer_driven__scan_mode (SDK 13) to SDK 14 (made changes in...
Hi,
I am implementing the whitelisting feature so that the NRF52 only pairs with one phone at a time. We require the NRF52 to advertise for 10 mins but I could only set...
IN looking at CONN_SUP_TIMEOUT below:
It says the units are 10 ms. if you take 4000 * 10 ms, you end up with 40000 ms which = 40 seconds - not 4 seconds.
Also for...
Hi,
As title, I'm the new for this.
I have one 52840 board and several 52832 boards, and one of them(sink) collect some data from other boards by using proprietary radio...
Hello,
We use nRF52832 with SDK-11 as peripheral in our project. We want to utilize white-list feature to limit the connection establishment. I have studied H ID Mouse example...
Hello, I'm trying to view the STATUS register of the timer (1 for example) but it is not display on the segger registers view ... Is it a well known problem ? Cheers, Sylvain...
I am developing application on nRF52832 with SDK14. I came across mem_section_dummy_rom and mem_section_dummy_ram sections in the linker script in the example codes. I couldn...
Hi
I have been using nRF52 in my project. I am not using provided uart drivers for one uart -> UARTE1. I am using DMA access and I have no problem to send and record messages...
