Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
I just bought a nrf51 dk to master this wonderful SoC series.
For now I intend to keep my research and studies with Bluetooth 4.1, but would like to prepare for a jump...
Will uarte interrupt call NRF_LOG_INFO, will run away the possibility of the processor? backend uses RTT
I set uarte receive dma buffer to 10, then the sender to use the...
Hi all, we have a problem with a project based in nrf52832 and a custom board. The project is based in "ble_app_uart" example, and also we have the following sensors:
Accelerometer...
hiii friends,
i have developed new board using nRF52832 xxAA. i am dumping code in this using nrf52 DK and it is working fine but when i am removing power from this and...
Hi, I want to confirm if the Mesh packet is a "special" form of advertising packet or it is completely different, i.e. all the headers and addresses etc are changed.
By...
Hi, I am using Keil to build programs less than 32 KB in size. All the example program from the SDKs work and I have read that should be the case because they are all under...
Hi all,
I'm going to use the latest SDK version of nrf51822 for my current project. Can you please help me to choice the right one for my development?
I want it as peripheral...
Hi all ,
I am learning theory about BLE . I'm exploring the relationship between layer . But I am quite difficult to understand the package structure from upper layer to...
Hi,
My config :
Board NRF52DK
SDK 14.2
Segger ES Release 3.30
SEGGER J-Link V6.22a
macOS 10.13.1
I want to use RTT to debug my code. As a starting point I've...
The manual clearly states that the external HFXO should be 32MHz. However, if one would like to have precise 16kHz on the PDM and I2S interfaces a 32.768MHz crystal is required...
I know that RF52840 could act simultaneously as the Advertiser\Peripheral and Observer\Central and I saw Nordic's recent demo video of BT + Thread co-existence. However, it...
I am having very limited knowledge in flashing devices, infact this is the first time I was doing it, pls conider
Step 1: I bough PCA10040 and installed nRFGo software in...
