Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I tried to assigned each device to different group(subscriptions) by the following code segment.
for (uint16_t i=0; i < devCnt; i++) {
......
ERROR_CHECK(config_client_server_set...
Hello Everyone,
I am trying to incorporate NFC-BLE pairing feature in my ble_app_uart example. I have imported all the necessary files to the project and have installed...
Hi,
I am working on the project as a MultiLink example. My environment is using nRF52840DK & Softdevice 6 & SDK15.
I am trying to make multiple connections and communicate...
Trying to understand how the Device UUID is derived.
in iOS, Device UUID: FC7C7422-2BCF-894B-E848-855791DD3DD9
in RTT:
DEVICEID0: 0E064007 DEVICEID1: 14669F75 DEVICEADDR0...
Hello.
Hello.
I am trying to install pc-ble-driver-js on my computer but it fails to install. If anyone could guide me how to install it, that will be appreciated...
I'm having a strange problem where the Supervision timeout does not seem to work right at the point the connection is initiated (sd_ble_gap_connect() was called but BLE_GAP_EVT_CONNECTED...
I'm using the SPI in slave mode and have a very high power draw: > 2 mA. The issue happens both in my application + custom board as well as with the dev-kit + SPIS example...
Hello
I just have some small queries.
Let's say that I am scanning continuously for advertisement packets. I think the MAC address of the devices sending these packets...
Hello
We have two boards PCA10040, client and peripheral. Blinky exemple.
The project is with two buttons on peripheral side and 2 leds on the client side.
If we hold...
i haven't seen any code posted for the HC-SR04 ultrasonic distance sensor connected to the nRF24LE1, so i rolled my own, see below. it works well enough. the sensor runs on...
Hi all!
I've been working on a firmware to timestamp GPIO events using PPI in nRF52, and it works:
github.com/HiveTracker/firmware (more context: hivetracker.github.io...
Hello,
We're preparing to build a new application based on the examples available in the Mesh sdk and wondering if you have any tips on how to extract only the files needed...
I run a basic code on nRF52832 and measure the power consumption of the chip (using DVM). The current consumption is 400 uA which is a lot just for a single timer in my application...
The tutorial is a huge help. I've been working on this for some days now, and it looks like I'm almost there. But just one last hurdle (I hope). The title pretty much says...
Hi Nordic Support,
I am trying to use BLE DFU. But for the first step I can not find the example that
is mentioned at this link: https://infocenter.nordicsemi.com/index...
