Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hey dear Devzone,
I am trying out some Thread and BLE dynamical examples on my nRF52840's but running into some problems using the " ble_thread_dyn_mtd_coap_cli " example...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
Hi there,
hope you are doing fine.
I am using SDK 14.1 with SoftDevice 132 as well as a state machine framework which needs a have a function called periodically to...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
When I want to disconnect central, I'm using sd_ble_gap_disconnect function as below.
err_code = sd_ble_gap_disconnect...
When I try to build and run any example from the nRF5 SDK, it can compile successfully. But when loading to the eval kit, it can't find the 's140_nrf52840_5.0.0-2_alpha_softdevice...
Hello Everyone,
I am using nrf51822 256Kb Flash and 32KB RAM Raytac's BLE module with SDK11, S130 with over the air Bootloader (16Kb).
So the aim is that when a particular...
Hi all,
I encountered a problem , when I connect 1 board central to 2 board peripheral via NUS . It connected and discovery success . But at
static void db_disc_handler...
I was compiling a project(ble_app_uart and I am using PCA10028), it was not successful and KEIL5 display this:
it looks like I didn't install NordicSemiconductor.nRF_DeviceFamilyPack...
Hello,
I use a nRF52832 device, and I have some strange behavior when I use PWM. You can see my test program listed below.
Thank for your reply, Thierry!
/*
* Test_PWM...
Hi. I am a newbie in Nordic chips, quite knowledgeable in Atmel AVR, though. I'm working with an nRF51822 on a board like this www.waveshare.com/.../BLE400 . I use the Mbed...
This might seem like a really banal question, but i could need some clarification on this.
My understanding is that the config_client should be used on the network provisioner...
I want to connect a ST Chip (LSM6DSL - Datasheet ) via SPI with the nRF52840 Preview DK (SDK13) - NRF_DRV_SPI_MODE_0
When I am using the SPI Master example with different...
