Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
use the SDK5 14.2.0, NRF52832, pca10040, the ble_peripheral\ble_app_uart\pca10040.
first, UART_EASY_DMA_SUPPORT = 1, run the uart_init(); the current is 1.2mA;
UART_EASY_DMA_SUPPORT...
Hello.
I'm having problems building example project from SDK using Segger Embedded Studio.
I'm using Segger Embedded Studio V3.30 IDE on Linux - Ubuntu 16.04. Using nrf...
I have a 24L01 + evkit in my hand and I want to burn my own program on this board, but I do not know how to burn it in. I have the following 3 questions:
Question 1: Where...
I have SD 4.0.2 + 13.0.0 secure debug bootloader, and I am trying to update it to SD 5.0.0 + 14.0.0 secure debug bootloader. It transfers the data, goes to 100%, but after...
Hi
I am currently working on a BLE mouse device. NRF52832. BLE part works well. However, the mouse stick part is using ps2 protocol. I didn't find USART in NRF52832.
...
Hi,
We face an issue since some days, i hope you will be able to help us.
We try to keep a BT connection between in nrf51822 chip and an IOS application put in background...
Torbjørn Øvrebekk from Nordic has made an example showing how to use AES CCM HW.
It does "work" self-consistently during encryption & decryption.
However, I think I found...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
was just wondering if there is a difference between the nRF1822 BEACON and the nRF1822 QFAC-R7?
the first one cost around $30 and the second one cost around $6.
I found...
Hello All,
I am trying to publish sensor data retrieved by nrf52840 to AWS mqtt broker.
has anyone ported amazon web service embedded C IoT sdk on nrf52 ?
Any suggestions...
I'm experiencing issues when porting a working app based on the BLE HIDS examples from SDK13 to SDK14. I now basically rebuilt the application from the SDK14 hids keyboard...
I was building a prototype on my nRF52DK. Before the weekend it all worked fine, switched it off, came back after the weekend and now I get the "Could not power-up debug power...
I made boards with the nrf52832 chip and the MAX8808X chip. The MAX8808X chip has battery monitoring. But I do not know what to do.
The number of GPIO pins connected to this...
Hello,
I downloaded the recent SDK 14.2.0 and installed nRF5x_MDK_8_15_0_IAR_NordicLicense.msi included.
When trying to load the ble_app_template in the dev kit I don...
Hi,
I have a custom PCB board with a nRF52832 and a motion sensor.
I cannot use a signal analyzer on the output from the sensor because of the shape and small size of...
