I am new to this forum and have some questions that I could not find elsewhere. The questions are:
Website asks me for a product key if I try to download the S210 soft...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Hello, I have been observing some interesting behavior concerning packets sent from server during eDRX idle period. When the period is set to 20.48s or 40.96s, any packet...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
I am using two nRF5340 Audio DKs one as a gateway and the other as a headset. I tested the nrf5340_audio example and managed to get the speaker output working through the...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic,
I want to implement a LED blinking like below pseudo code. I'd like to use PWM sequence Timer x n , GPIOTE, PPI since it doesn't consume any CPU time. for ...
The functions “ nrf_log_frontend_std_...() ” called by “ NRF_LOG_INTERNAL_MODULE(...) ” use only 4-byte (uint32_t) arguments, which is not suitable for arguments of type ...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
Hi,
I am trying the system_off sample of Zephyr version 4.0.99: https://docs.zephyrproject.org/latest/samples/boards/nordic/system_off/README.html
The sample works...
Hi,
I have a problem with nRF52832 after entering the radio RX state. I use a proprietary protocol with fixed packet length. Packet transmission works fine, receiving the...
Hi, We developed our custom BLE electronic board based on the nRF54L15 SoC. On this project the nRF54L15 firmware setup a SPI slave interface in order to receive commands...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
