Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear sir,
I use nRF52832 for our product. But I change PCB antenna to chip antenna, modify match circuit. At this conditions, which bluetooth SIG certification process should...
Hello everybody ! Designing with the development board nRF52832 and SDK14.2.
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the...
Hello, nordic.
I have added uart functionality to hrs example, to add OBB pairing to uart example.
I have replaced as hrs --> nus and have inserted uart_init(), uart_event_handler...
I want to connect esp32 with nrf52840 for availing Bluetooth 5 functionality. In this, I want to use esp32 as application processor and nrf52840 as network co-processor. Is...
Hi everyone,
We develop the project on chip NRF52832 with SDK v14.0.
The chip in this project works in multirole mode. During the work it must scan the devices to acquire...
In order to transmit sensor readout from an I2C sensor I have to write new software for the nRF51822 to use the I2C bus and need to change the Android app for displaying the...
I've read, that a provisioner/client in an application like the lightswitch example can only manage up to 50 nodes (servers), using persistent storage on a nRF52840 device...
Hello Recently, after a long time not using my Thingy52, I encountered a problem with it. I cannot connect to the device. Earlier it worked fine (can't remember if it was...
Hi,
I've just bought nRF Dongle and wanted to start using it with nRF Connect app for desktop, however nothing happens when I plug it in: no sound of connecting a USB device...
Hardware:
1. STM32L476, nrf52832
Software:
1. SES(Segger Embedded Studio)
We had finished our production development on Keil, and right now we want to transplant platform...
HI team,
I like to interface methane, hydrogen and moisture sensor in my custom board which is going to use nrf52840 soc. i am in development stage. for outdoor application...
I would like to know if there is any documentation that speaks of security for push notifications. For example, that talk about security when using a nRF52 device as a beacon...
Hi,
Is it possible to make infinite GATT connection ? I set auto connect in android central app and my program in nrf51DK works. But only 4 hours.
Hardfault is almost...
When I try to build example in SDK 12.3.0, I always get the hex file for nRF51422 target, how should I change the target to build the example for nRF51822?
I set the variables...
