Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi All,
i would like to know how gpio relate to gpiote,i go through some code and find
out , that gpiote handles in,out,config registers that is handle by gpio also ...
Hi nordic guys,
I have built a project based on ble_app_hids_keyboard demo in SDK12.3.0.This is a new hid deive which is microsoft defined in win10.The sample report is...
I have few questions on BLE in rigado based on my requirement needs,
I need Dynamic data transfer in beacon mode, is it possible in Beacon mode without Rigado BLE stack...
Hello,
I get two errors when compiling examples\ble_peripheral\ble_app_uart with IAR 8.11. I have ble_app_uart_pca10040_s132 - nrf52832_xxaa as the active project.
I...
registered_handler_get() in ble_db_discovery.c searches a table for the appropriate handler to call for a given UUID.
However, ble_db_discovery_evt_register() assigns the...
Hi,
In the Getting Started guide of the Bluetooth Mesh SDK it is stated that legacy non-mesh devices can communicate with the mesh via a proxy mesh device through tunneling...
Hi everyone,
I am using the PCA10001 eval board and I have been able to get things up and running using the mbed platform but now I am implementing a timer based interrupt...
Hi All,
I'm currently designing my implementation of BLE Services/Characteristics and wanted a quick review to make sure I'm on the right path based on my implementation...
Hi,
I have couple of nRF52832 boards, nRF5-SDK-for-Mesh (v. 0.9.2) and good will to demonstrate some simple multihop mesh.
I already tested the light control example...
Hello,
There is gonna be a tech tour in my country(Israel) soon and I am planning to purchase 2 nrf52832 Development kits does anybody know if it will be available there...
Hi! I want to use the "cube" animation from android thingy app, with my custom board.
When I scaned in first place I couldn't see my board. It was solved adding the ble_tcs...
Hi,
Is it safe to backfeed some current into the PPK.
I use the PPK to measure the power consumption of a battery powered IoT device. I disconnect the battery and use the...
It looks like the "NRF52-DK" development kit I can find comes with an nRF52832 chip, but I'm looking to get a dev kit to develop for the nRF52810. I did also find a "NRF52840...
Hi: it's me again, sorry to bother everyone once more.
This time I can finish provisioning... almost. You see, at the end of the whole provision process, a function must...
Hello,
A stupid newbie question: APP_UART_FIFO_INIT seems to get stuck while trying to run
example code.
Only modification I have made is the usage of SEGGER_RTT for...
