Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
hi all
I am facing the issue that the chip still retains in debug mode. SWDCLK pin has connected to GND directly.
steps:
1. after flashed hex file, removed debugger...
Moving from SDK14 to SDK15, I noticed that USB takes long time to make connection (20 - 30 seconds). Comparing nrf_drv_usbd.c, I realized that the "shortcut between EP0DATADONE...
Hi Nordic team
I want to switch between DTM and normal BLE by pressing the button.
It is base on two example ble_app_att_mtu_throughput and direct_test_mode.
Is there...
Hi,
My central device should scan and should get DIS of one peripheral and store in central and central should pass this information to other peripheral .
or
Central...
I am using nRF52832 with Beacon_App. I can able to get UID, Major, Minor, RSSI from my Raspberry PI using Python code.
I want to calculate the distance between my Raspberry...
I'm using S112 and SDK 14.2 to target NRF52810, but using the PCA10040 DK for now.
I've been coming back this issue multiple times over the past couple of months, still...
Hi @ll,
I tried to get the dfu example up and running but there are a lot of problems I encountered:
- Using the device_page_generator.py the string for the public key...
Hi @ll,
I have a problem bringing the pyaci up and running.
I used it successfully for everything before but since today it is making a mess again:
When I'm trying to...
I am using secure dfu bootloader from the SDK 12.
I changed the start address of my application. In the bootloader, in uint32_t nrf_dfu_init() { } , calling function nrf_bootloader_app_start...
Hello,
I want to make a simple UART Bridge between Central and Peirpheral. I'm usign nRF52832 with nRF5_SDK v15. There are central and peripheral uart examples in the...
Hi,
I have a working application with Buttonless Secure DFU Service wich runs on nRF52832. I'm able to perform DFU without bonds, but I want to use bonding in my application...
Direct connection after disconnect I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection...
