I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
I need a reference design of nRF51822 for minimum 1 meter range . The circuit will run from CR2032 battery for at least 24 hours and will take some readings from ADC input...
i am unable to sniff the packets between two devices once the connection is established between two devices..i am using nRF sniffer 1.0 ...
i am able to see only the advertisement...
Hi,
How can I control the PDU error code when reading an attribute.
E.g. Attribbute not found 0x0A. For more info see 3.4.1 Error Handling Bluetooth spec 4.1 Volume 3...
Hi,
I have created a custom PCB that more or less follows the Nordic SmartBeacon design: Beacon_V2.pdf
Instead of BAL-NRF01D3 I used the BALF-NRF01D3 as this is supposed...
I have use random number generator in S110, the source code just like:
uint8_t num_rand_bytes_available;
err_code = sd_rand_application_bytes_available_get(&num_rand_bytes_available...
what does it mean the VTG led turn red ? but it has no bad effect to my project. In addition, I find a strange phenomenon. I use three 1.5v battery to power my board. The...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi nordics!
First of all, thanks for answering my questions before.
Now, I want to generate a clock(48 pulses) with 200us width.
However, sometimes the width of...
Hi ,
I have a application program which uses s110 and UART service .
The issue is the program is not working when I enable the Micro Lib in keil.
On observing the map file...
Hello,
I want to use flash for logging sensor data and sending via BLE.
I found several APIs for store data to flash.
pstorage (Persistent Storage Access Routines...
Hi all,
I would like to know how can I program and debug the nRF51822 development boards?
I've seen some boards have a built-in programmer and others haven't.
How can...
In the DFU code provided by nordic is explicitly states that.
"Soft reset from application must not reinitialize the SoftDevice."
In my application I do not have a button...
Hello,
I have made simple modifications to the multilink central and peripheral examples, adding an additional button and notification characteristic. Things have been...
We're designing a board with the nrf51822 QFA part. Due to design constraints, the chip will have to be about 15mm from where the antenna port will be. The routing to the...
