I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I have a problem with some beacons which don't follow BLE specification.
Namely BLUETOOTH SPECIFICATION Version 4.2, 4.4.2.2 Advertising Interval section.
The problem is...
Hi,
I'm not sure whether it is right place or not to discuss this.
We are planing to use nrf52840 in our new IOT project. We required nearly 30 development boards and...
I don't want my consumer to do provisioning of mesh-DEVICEs one by one (using Android or iOS APP) since in such case if he has 50 mesh-Devices in that case he will get frustrated...
Hi everyone,
It looks like there is a bug in GZP host example.There is a function gzp_host_chip_id_read where flash is accessed at GZP_PARAMS_STORAGE_ADR. But there is...
I am using the following to extract the Device_Name from an advertised packet received on an Arduino Primo:
peer.getFieldInAdvPck(BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME, advertisedName...
Hi!
I have a question about the Mesh SDK. Is it currently possible to get the physical source of a relayed message (thus the relay that send it) out of it? I only seem...
I use buttonless_dfu_app as template. SDK 14.2
Q1. Could someone help me.. After I updated my app I have changed crc (if more than just few changes), so bootloader installed...
I made all steps in a guide
devzone.nordicsemi.com/.../
All works fine. After that prepare my own firmware like appendix 1. Also works good. I merge
bootloader_setting...
Hello,
i'm trying to run the ble_uart_example on my nRF52840 eval-board, but it always fails on this line:
err_code = ble_advertising_init(&m_advertising, &init);
APP_ERROR_CHECK...
Hi, everyone,
I develope the project with BLE support. In my project I need to define the time server. For this purpose I tried to find any example reffered to it, but no...
It is a sensing-processing-actuation based application. Just want to use the nRF52832 module for BLE communication( a part of the application).
Is there a direct API in the...
Hello,
I have an application where an nRF52832 peripheral (S132 v3.1.0) transmits a 5-to-10 MB file to an nRF52832 central (S132 v4.0.5). The peripheral sends the file...
Hello,
I have bought an nRF51 dongle with a SEGGER J-Link.
I have downloaded all the SDK and everything from nordic website.
If i open an ble peripheral example in uvision5...
