Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi, I have issue where the slot 1 image seems stuck. It can not be erased, confirmed, or swapped in the state that it is currently on. When I click erase, the error bad state...
I'm writing an application for the nRF54L15 that periodically receives the local time via bluetooth and keeps track of time on its own between syncs. I'm using a 10ppm external...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
In Electrical specification Table 1 (current consumption in forced High Power mode) lists a typical value of 7.2 mA , just want to confirmed this is correct and not a typo...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
I have a single-ended signal that spans [0V,3.3V] and is centered around V_bias=1.65V (=3.3V/2).
I want to use the NRF54L internal gain to amplify only the AC parts of the...
this my yaml.file to use partition manager, beacause iam implementing DFU, USB MSC with fatfs in single project
fatfs_storage :
address : 0x00000000
size : 0x00200000...
Hi, I am using custom nrf52840 board with sysbuild, MCUboot+firmware loader, static partitioning, settings storage (OpenThread) and littleFS storage and I cannot get the thing...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Hello everyone.
WE're trying to make a https connection with google.com and execute a GET request.
Wifi connection is working; DHCP seems to be working (my personal assumption...
