Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hi. I've seen many questions here regarding BLE throughput, I've been trying to get something better than the 200 B/s I'm getting.
I am using a nrf52832 as a GATT server...
I tried to sniff Mesh Packets send with the Light Switch Example but I didn't get any.
For sniffing I use the nrfsniffer v2 with the nrf dongle and for the Light Switch...
I'm trying to get nRF UART logging to work and have included all the nRF_Log libraries as per the blinky example (which works).
However, upon building, I'm getting
"nrf_fprintf...
I am currently using the NRF24l01+ but i want to know if I should be using a different product for my application. I am sending very small amount of information (such as hex...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I have a client device that normally is able to call ble_db_discovery_start and get the callback just fine and is able to complete the db discovery process. However sometimes...
I try to use SPI with easy DMA, in page 279 in the datasheet says: " An SPI master transaction consists of a sequence started by the START task followed by a number of events...
I have an issue with waking up SPI communication after sleep.
Befor I go to sleep I'm disabling SPI communication:
NRF_SPI0->ENABLE = 0;
NRF_SPI1->ENABLE = 0;
...
Hi is there anyone who knows if you can change the time on how often the health server model send out, the health server model is from lightswitch demo
Hi,
I wanna use nrf51822 as master which has 2 slaves: sdcard (fatfs) and adc
I set SPI_INSTANCE 0
and they don't want to work together, I mean I'd like to write some...
A time T_PINR is specified in the datasheet, as shown in the snippet below.
Does this give me an indication of the pulse width for a pin reset? If so, how do I interpret...
Not really a question, just that I find the comment misleading. In the sdk_config.h example coming with the SDK there is this piece of code:
// <q> SAADC_CONFIG_LP_MODE...
Hello,
I am trying to establish communication between Win 10 PC and nRF52 Dev Kit using pc-ble-driver . I followed the instructions in:
https://github.com/NordicSemiconductor...
RN2903 is LoraWAN module using ASCII Command Interface over UART.
RN2903 is connected with nRF52-DK.
I'm connected uart line tx, rx gnd.(cross connect...)
UART communication...
Hi,
My desire is to connect a BC832 module (with nRF52832 on it) to a UART on a controller board and then send data from an iOS app (programmed in Swift) through the BLE...
