But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hi,
i am creating a new project iar workbench 7.8 with SDK V8.1.0 and softdevice V8.0.0 using custom board nrf51822 ic revision 3 (QFAAH00),clock source as "NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
Hello Sir,
I am designing PCB using nRF52832 SoC it is very small and operated on AA battery source.
So please recommend me for reverse battery voltage protection diode...
Hi Guys,
Me again. I was thinking someone could provide some suggestions on my understanding of the BLE connection ( porfile, GATT, characteristic,value, etc...)
I finished...
I had successfully write a structure data to fds. After which, I would like to update the same file and record key with new values of a structure. After updating, I will read...
Imagine I have developed a MESH made up of 50 Relay Nodes and I say only Relay Nodes because any of them must be able to relay and also able to initiate a message. In my application...
Hi,
I am making a GPS tracking system using NRF51822-QFAC. I am using 2 UARTs, one of the (external) GPRS IC and one for (external) RS485 communication.
The UART peripheral...
HI,
I tried to compile Thingy v2.1.0 with keil. And sereval file are missing.
Actually i work with your SDK 14.0.0, i find so many missing file, but not all.
Can...
Hi,
I am currently testing with a USB MSC example .
FATFS_QSPI is disabled because the file system is not used,
Subclass has also been modified to 0x06 -> 0xFF.
...
Hi,
I am implementing experimental_bootloader_secure_usb code example on PDK PCA10056 V0.9.2 using Sdk v14.0 and also tested with Sdk v14.2 but in both cases Windows 10...
With SD140 v6.0.0.6 having been released, will an accompanying example project that demonstrates simultaneous use of BLE and USB be released? Will this be included in the...
Dear devzone,
I am currently merging the Mesh SDK into the normal SDK to run BLE & BL mesh concurrently.
Followed multiple guides to get it working, at this moment I am...
I use nrf52832 development kit,nRF5 SDK for homekit.
Now I have read and write to UUID, want to realize how to handle the notification operation, and call what API?What are...
I enter to bootloader via my app by UART command:
err_code = sd_power_gpregret_clr(0, 0xffffffff);
APP_ERROR_CHECK(err_code);
err_code = sd_power_gpregret_set(0, 0xB1...
I know nothing about bluetooth
like ble_app_uart , uart to where?how to use this uart?
like ble_app_alert_notification, alert? beep? vibrator?
any tutorial of develop...
Hi. I am connecting to and establishing a bond between my Android phone and the nRF52832 board using the s132 SoftDevice. I'm in a situation where the Android phone has a...
