I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hi All,
We have build a BLE beacon device based on the nrf52 chip. The device works fine but we would like to get a finer control over the TX power since it is used for...
compiled nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_rscs example but will fail on adding chararteristics in char_add() setup: SEGGER Embedded Studio for ARM Release...
Hi guys,
I am trying to use a TM2001 amplifier ( Taiwan Microelectronics, google returns the PDF) to amplify the signal from an nRF24L01P.
The TM2001 seems to accept a...
Hi.
I want to create Bluetooth mesh network and I need that each of device at first must be provisionee, but if in a minute it hasn't been added in a network by provisioner...
Hi
I was designing a custom board for nrf52832. The 32MHZ crsytal mentioned in the refrence design of nrf52832 is not available on digi key. So I am ordering the below given...
Hello,
I have a string data and I want to get a part of it which start for example with "hello" and I want to get 20 characters after "hello".
(for more details I'm using...
in the demo of EnOcean switch translator client,there is just enocean_switch_nrf52832_xxAA_s132_6_0_0.emProject .is it use the same demo as client in the example of light...
Hi, I am using nrf SDK for mesh and try to add FreeRTOS , but after adding build failed because both has files with same name. Is it possible to work with FreeRTOS and nrf...
Hello;
I want to scan beacon devices (UUID infos) every second with Arduino Uno + nRF51822
I could not find a sample on the site. (Arduino Code)
Is it possible? Would...
I've gotten a good handle on how Gazell interacts with devices and the host, but I am running into an issue where there are higher rate of failures when using two devices...
