Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I've gone through the user manual for the Nordic Power Profiler Kit, but I can't find any basic information on how to understand the plots and the measurements reported under...
I would like to have one central and two peripheral connection. Ad functionality required is same as NUS UART Example. But the example code connects to only device. Can any...
Hello,
i would like to connect two Redbearlabs Nano v2 just with eachother. The central one connects just to the peripheral, but the peripheral is still open for every...
Hello There,
I found following dongle based on nRF51822.
They claim same will work for bluetooth 5.0 also.
I know BT5 devices are not backward compatible, so not sure if...
Hi,
How can I share a GATT server profile constructed on nRF connect for PC with nRF connect for Android ?
'Save/Load setup' on Windows PC stores/Load json file
In...
I've got a set of boards that are behaving very strangely. I attempt to turn on the HFCLK but the HFCLKSTARTED event never comes nor does the HFCLKSTAT register indicate that...
I cannot suffer this tool anymore. As u can see in the pic below, it provides a cursor mode to measure the currents of X1/X2. However, users always need to know the average...
Hi,
I want to connect 4 antennas to nRF52832, they respectively points to North, South, East and West direction.
Also I hope the nRF52832 can do switch antenna job,...
I'm trying to use gcc and eclipse but I'm getting an error in eclipse that certain variable names cannot be resolved. I know that its not being able to get the variable names...
Hi,
I am developing a small development board of visiting card size, which is powered from a coin cell. I have two questions,
All i want know is there any polarity...
Hi,
do sd_flash_page_erase or sd_flash_write provide any guarantees that the command has executed successfully or should I do a manual check to verify if the page was really...
Hello all,
I am working on nrf52832 Board and i want to use it as translator to send and receive the data , please tel which pins i need to select as UART(rx,tx) pins ...
I am designing a custom board with nRF52840, powered by USB, no battery, using its internal LDOs to supply other peripherals with 3.3V
I have two questions about pins/outputs...
Hi
I generate a pwm signal via changing the state of one characteristic. In general, the pwm works fine. But the problem occurs when I add the timer which is responsible...
Hi guys，
I use the 51822's PWM recently, PWM is made by GPIOTE+PPI+TIMER, and the PWM source code as below(I use TIMER1, GPIOTE[0], PPI_CH[0], PPI_CH[1]， period and duty...
