Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
hi
I have a application use NRF52832 to scan beacon's advertising and write the advertising data into NRF52832's advertising.
I found the working current is nearly 3mA...
Hello,
I am useing NRF51822-QFAC in my BT bridge project; Now I need to design the matching circuit; there was some recommended matching circuit in the datasheet(11.3--11...
I have a central device that uses BLE to scan for a specific device (there is only a single device it can bond with). Right now it checks the UUID and the mac address of all...
my device giving output as square pulses.but would like to control current from the range 50uA to 500uA of square pulses.how to calculate it. can someone help me
Hi,
I have a question that Product Specification v3.1 of nrf51822 describes Flexible Power Management: 2.6 μA at 3 V ON mode, all blocks IDLE. But, in the same place, NRF52832...
Working on migrating my application from sdk 12.2 to sdk 14
except for some flash issues most of it seems to be working as before, except I notice this message in jlink:...
Hi,
I'm using SDK 14.2.0 flash_fstorage_example_s140_pca10056 with SEGGER on the nRF52840 Preview DK.
As you can see the basic example not working, what I'm writing...
I got the ble_app_lbs example working using SDK 8.0.0, and am now trying to integrate it into my existing project which was based off of ble_app_rscs using SDK 11.0.0.
...
Hello,
I am trying to intergrate the blinky, timer, and UART examples.
Blinky and Timer examples seem to work fine.
When I added UART, linker error starts to show up...
Hi,
Follow answers from here and have many try, not success yet.
Development with GCC and Eclipse, can not reach main() but return "Programe file does not exist" when...
Honorable technician, hello
I am adding a dependency Library for DFU by Android studio,find " compile 'no.nordicsemi.android:dfu:1.3.0' "and “ implementation 'com.android...
As the title says, I'm having problems connecting to my device with my custom board and I don't know what else to do. This is my Layout:
Whenever I upload my firmware...
I found nRF52832 modules like www.ebay.com/.../332270581440 on eBay, but there's no documentation for them except the board pinout. Has anyone tied them? How are they shipped...
Hi All!
I must to add some binary data to ADV packet use Manufacturer Specific field.
I fill the related fields:
static uint16_t adc0_data = 0; // ADC measured data...
