Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
Hi, guys! I am working about a project that I need to get data from sensor and send these data through mesh. I referred from link text ,and the example works well. But, I...
I'm looking for a Nordic expert. I have already designed and built a complete PCB based on the Nordic nRF52832, along with the firmware. I need to improve the PCB design,...
On my nRF52 DK, I'm seeing *something* pull down VCC by about 50 mV once every millisecond (1KHz), and I'm trying to identify its source. (This is only important because using...
Our application needs to read 128 bytes from 6 SPI sensors as efficiently as possible. We're currently using a single SPI Manager to read all 128 bytes from all 6 sensors...
Hi all.
Just wondering if i need to go through the tutorials on making a service if i just want to read a few bytes in an advertising beacon.
I'm a little lost on figuring...
Hi ,
I am using a bluetooth peripheral which have the Custom Service ID and characteristics ID as below.
Service UUID: 56494B01-0100-1000-8000-00805F9B04E1
Characterisitics...
Hi,
We are currently developing an application that makes use of soft device(s112). We tried using timer(Timer 1) for a timed wake up and sleep but found that the actual...
We are seeing an LMP PDU error when connecting to a Nexus 6p with Oreo (8.0.0) when connecting to an nRF52832 utilizing SDK 14.2 and either s132 vs 5.0 or 5.1 anytime NRF_SDH_BLE_GAP_EVENT_LENGTH...
Been testing custom_ble_service_example , specifically to see if a two byte custom_value can also be used.
But when setting custom_value to uint16_t I get a warning at this...
Hi, I would like to use a PWM application with mesh SDK. However when I try to compile, I got an error because "app_pwm.h" is missing (No such file or directory). The only...
Hi !
I'm using the nrf52832 chip and I'm trying to communicate with a LIS2DH12 accelerometer using the I2C protocol.
But unfortunately I can't handle with it, it seems...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
Hello,
I am using sdk12.2.2 and customised nrf52 board. I am writing 6000 records of 24 bytes each in flash of nrf52. My challenge is after 6027 records I am getting error...
i made custom board refer to thingy 52 Circuit
all fuction circuit is same so i want to use thingy 52 firmware
when i was erase all memory nrf52832 and upload thingy_v2...
