Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi, according to the Bluetooth Mesh Glossary , there are 4 features supported:
1. Relay;
2. Proxy (GATT);
3. Low power;
4. Friend.
Questions:
- Which of these...
We are releasing a firmware update which adds an additional bluetooth profile. Since we do not want or can retest the entire stack, we use a Previously Qualified Design (51744...
I'm using NRF51822 with soft device version 6.0.
I'm trying to create an event which should be triggered every 24 Hours. In the current implementation in our code base...
I saw the demo of nRF52832 connected 20 peripheral devices and control the light in the peripheral.I would like to know the more deatil of the whole operation in chip/SD....
I've searched and the majority of answers seem to be years old.
I have an existing app_timer event handler that works perfectly, blinking LEDs.
I will soon have another...
Hi! I'm using two RedBear Nano v2 and I'm trying to read a long characteristic from one of the two devices. As I read in other posts in the forum, I need to invoke the read...
If I'm not mistaken, both S110 and S130 support OTA DFU right?
I understand that nordic semi most likely recommend S130 over S110, but please understand that
my current...
I have previously developed on the nRF24LU1+. This device would have a CHIPID in the InfoPage, This ID would have guaranteed it does not violate the requirements for ESB addresses...
Hi, im using NRF52832 whit SDK 12.3.0, when i compile this error appear, "undefined reference to `nrf_drv_spi_init", i included the "nrf_drv_spi.h" file.
also try to include...
Hi everyone,
I'm working with nrf52832 and i'm trying to send data over BLE for communicate with a mobile app. I saw that we could pass data with the function ble_nus_string_send...
Minor nitpick:
The PS_v1.0 datasheet says that "see the Reference Layout section on the Downloads tab for nRF52840 on..."
There is no Reference Layout section on the Downloads...
I am working on a BLE bootloader using SDK 14.2.0 on an NRF52832 device, using softdevice version 5.0.0. I am able to get the bootloader up and running, and I am able to see...
Pre Conditions:
1. As soon as the connection is established the App start a timer to disconnect the link using sd_ble_gap_disconnect
2. The app timer has the same timeout...
Hello,
I'm searching the possibilities of Thread mesh network. And I want to minimize the size of border router as small as possible. Have you considered to port the border...
