Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi All,
I am using the nrf_udp_client example project in IoT SDK as the code base for testing the UDP communication.
For network topology, the nrf51-DK plays the role...
Hi everyone:
I have some question about nrf51822 power on sleep mode
in example ble_app_hrs have a "power_manage" function and it will make the system go into power...
Hello all,
I have a simple C++ application flashed to my device to operate the UART - every time I send a char from an external source, the device appears to reset - specifically...
Hello
I was wondering if it is possible to run to separate LP-comparators on the PCA10001? I've taken a look at the example code for LP-comparator in the SDK, and i was...
I'm using interrupt_handler.c for a bootloader without a softdevice from this source . Interrupt handling in the main app seems to work fine. But interrupts in the bootloader...
Hi,
In the nrf51_bitfields.h file, I can see definitions for two registers POWER_RAMON and POWER_RAMONB.
But I don't see this RAMONB in th nRF51 reference manual and...
hello, I bought one of these dongles on ebay www.ebay.com/.../201229095155
i was hoping to communicate to the nrf24l01 modules with my pc serially, but I can't get the...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello there, I do not understand the definition Nordic has provided for the "SPI_slave_event_handler_register" function bellow. My understanding is when SPI slave driver occurs...
I need to write to a variable when a particular characteristic is written (from my "on_write" function), and be able to read this variable from main context.
From the SoftDevice...
Hi everyone :
I'm trying to used ble_app_beacon and I want to combine it into ble_ app_hrs
so i add some code as followed:
static void advertising_init(void){
uint32_t...
We're sending packets from a nRF51422 usb dongle to a nRF51422 dev board running some modified Nordic UART example code. We send 100kB of data over the connection to work...
Hello :)
For the code below, why are we defining the _wfi while in the code we only use _WFI() for addressing the function? Also once we use _asm volatile ("wfi); isnt the...
Hi:
my sdk is about 96k,and i use 51822QFAC,but it's flash is 256K,(256K-88K)/2=84K,so it is not enough for me,how should i do,if i add a external flash is ok or do you...
Plz help me with code or sequence of steps being followed by _WFE() or power_manage() functions. by which they manage the nrf51422 to run in low power mode.
So that i can...
