Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello,
I am currently working with the nRF5340DK and the W5500 shield. Both work perfectly when using the dhcpv4_client application. However, when I attempt to use the recv...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
I am considering using the nRF51822 for an upcoming project for a client. It is a simple BLE peripheral, so I would use the S110 SoftDevice for the stack. I am looking at...
I use BLE mesh github.com/.../nRF51-ble-bcast-mesh
but when I use the master control to write values to update the values of services, the following error occurs: "global...
Hi,
I have implemented the support for 'long write' as in
github.com/.../ble_app_hrs---LongWrite
which works from the MCP... except that on BLE_GATTS_EVT_WRITE, it seems...
I have bought nrf go starter kit with pca10005 board( nrf51822 ic). I want to program the nrf51822 using these tools.The guide that I got from the nordic website not explaining...
If the device is paired (but not bonded) using "Just Works", sd_softdevice_disable() causes the application to hang/crash (nothing happens until reset by watchdog timer)....
I want to generate 2 fast PWM waves with 25% duty cycles from nRF51822. They have same frequency of 4MHz but there is half a cycle delay between them. I checked the nrf_pwm...
Hi,
I am trying to get the NRF8001 rev. C chip working with a Tiva Lauchpad (TM4C123GXL) board. I modified the original Arduino SDK for use with Energia. I am using the...
Hello,
i want to write a global unsigned long variable in RAM after programming the device. The Use-Case is to set the clock value to the actual time. So the new unsigned...
I use BLE mesh github.com/.../nRF51-ble-bcast-mesh
but when I use the master control to write values to update the values of services, the following error occurs: "global...
Hi. All.
I am in the process of update SDK 9.0 from 5.2.
Meanwhile, SPI couldn't read from external flash's data.
Unusually SPI works well before infinite loop, I tested...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
I want to use the nRF51-DK board as a programmer for my target. As I understand it, this can be done with the signals on P19. However, there is one signal, EXT_RESET, that...
github.com/.../nrf51-UART-examples
Hey any I was trying to test the example, the one with BLE
I test
APP BLE sending --------shows on PC UART software
However, I can...
Hi,
I would like to ask if someone has experience using the AES. I n eed to be absolutely sure that the user SW can use the AES HW block for own custom usage. If yes, Are...
