hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I am using arduino to sample sensor and it sends out the value to the digital pin. I want to read this digital value using nrf51dk. Is there any example using digital...
Hi Nordic Tech support team,
I have some questions about nrf51822 dfu OTA.
Nrf51822 application code can't be more than 144K，however ，my application code have 196K because...
we follow the nRF51_Series_Reference_manual v3.0, set the master SPI clock to 8M. but found when in mode 0, the MOSI change near at SCLK rise edge, not in fall edge.
our...
This should have been a very simple question. I don't want to use CTS/RTS flow control signals with my UART-USB-converter ("FTDI chip"). For that case, the document says ...
I want to highlight some items in RTT Viewer
So I tried the color control, but didn't work
This is my code.
SEGGER_RTT_printf(0, "%s[Mutex error:%u]\n%s", RTT_CTRL_BG_BRIGHT_RED...
Hello.
I am trying to port BLE serialization code to a host MCU, to say STM32F4.
I am looking through porting documentation (BTW, it is quite well documented. Well done...
According to Microsoft's instruction on HID touch device, msdn.microsoft.com/.../dn672271(v=vs.85).aspx , a HID touch device should create a report (descriptor) as below,...
Hi,
I am having a 324 byte,a 420 bytes of array stored in flash,now i am updating these array with 360 bytes. in fds_event_handler in the case FDS_EVT_WRITE i am reading...
Hi,
I'm looking for an example which combines FreeRTOS, BLE and ADC on nrf52 board(10040).
I'm able to have FreeRTOS with BLE, FreeRTOS with ADC but not everything together...
Hi,
I've read a lot of question on the forum, but I'm a lit bit confused about what I have to do to use one static passkey on the central and peripherical device. In my...
Hi There,
I'm having problems with my hardware timer appearing to stop counting or not being cleared via a short when the timer interrupt is executing.
In my application...
Hey!
I want to use the nrf51 BLE-module in some special environment.
It should be able to work with bluetooth and in addition to it with some other RF protocol (Gazell...
Hi,
I have added "DFU" functionality to my existing BLE application Test.rar .
"I am using nrf52 SDK v11.0".
I have programmed the device with softdevices (S132.hex...
