Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I'm using an external chip that decodes my RF transmission and outputs the data on two pins DAT, and CLK (data and clock). Currently I'm reading the data with GPIOTE...
We have written our own softdevice, but now we have a question about the stack pointer.
I read in the softdevice specification that the nordic softdevices share the stack...
I have been trying to establish a link that will feed sensor data into my com port via a Bluetooth uart bridge. I got my closest today by doing the following.
Load SDK10...
I'm having trouble making a single bank dfu mode with 128k NRF51822 chip.
Here's the problem;
Works fine when everything(SoftDevice, Application, Bootloader) is all...
Hi,
I am a newbie to Nordic BLE.
A make error occurs when building the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0 on my cross compile environment...
Good morning, i have windows 7 and at this moment i have installed "Gnu tools for ARM embedded Processors", "GnuWin32 ‐ GNU Make utility", "GnuWin32 ‐ Core Utility", "nrfgostudio...
Hello,
on our custom hardware design, the hardware reset won`t be executed after programming with nrfjprog.exe, until complete new boot with disconnecting Vcc.
After reconnecting...
We are going to use nRFgo - Bluetooth direct test mode to evaluate the nRF51 device RF performance, and we need to load the DTM (Direct test mode) application to the device...
Hello
I have an nRF51822 serving as s supervisory micro for an embedded Linux board. Two GPIO pins from the main CPU are hooked up to the nRF51822 to implement SWD for...
Hello.
I'm using nRF51822, nRF51_SDK_8.1.0, and looking for same useful sample code for ble central with HoGP (HID over GATT Profile).
please let me know where is it...
Hello,
Is there someone to confirm than Keil MDK-Cortex-M edition is OK to develop app on nRF51 and nRF52 Nordic chips or do I use MDK-Standard?
www2.keil.com/.../
Hello everybody,
Maybe some of you using Eclipse and GCC have encountered the same problems when you try to start a debugging session.
First of all: If you have Bluetooth...
Using and GCC with compilation options without optimization -O0 and with debug -g3 throw error during compiling for an unknown function pwm_calculate_timer_frequency .
...
