I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Some examples require SDK 7.1, while the newer tutorials use SDK 8.0. I'm not sure how to switch between the SDK versions in Keil. I see the below lines in my include paths...
Hi.
Currently, the following results came out in the power-saving support .
■Our App
・Advertising Status
1.04mA ~ 1.13mA
・Connection Status ★1
1.044 ~...
Hi.
After stopping the Advertising,I measured the current.
For some reason, usually it is consumes about 1.1mA.
Because too large current consumption,
As a result...
Hi I using nRF51822, and want to know about the Nordic driver support LMP feature
Do you have any document about driver support? Or any software development document except...
Hello, I need to create a high resolution/high frequency PWM signal on the nRF51822. I have been using the new PWM library in the 8.1 SDK and can't quite get there.
From...
Hello. After a couple of s210 and s310 projects, I am attempting an s120 project. I built a client SDK but sd_nvic_EnableIRQ returns error code 0x2009 or NRF_ERROR_SOC_PPI_INVALID_GROUP...
I'm running the "Beacon Application for Eval Board" example for the S110 soft device on an nRF51822.
( devzone.nordicsemi.com/.../a00070.html)
I'm using another BLE...
Hi,
I was wondering if it is regual that configuring softdevice for a low frequency oscillator 32.768 kHz using the function:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
Hi:
I use SDK7.2.0 encountered a problem when I was disconnected, has reached the maximum number of bonding, I want to remove the first bonding information. I do not know...
