Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
If I set the I2S peripheral on the nRF52 to mono, ie CHANNELS is either LEFT or RIGHT, what does it actually output? I'm sure it still toggles the LRCLK line to indicate left...
I'm working on a battery - operated device where the battery is soldered onto the device, which makes it inconvenient to pull power to the device. I might be able to get to...
Hello,
I have some problem in DFU.
I ask this again.
I did as below.
Key generation
nrfutil keys generate c:\vault\priv.pem
public key generation in...
Dear Nordic Team,
I can't launch Sniffer on PCA10000 using MCP nor on PCA10040 using nrfConnect. In case of MCP I get "No response from master emulator" and in nrfConnect...
Hi,
is someone of you aware of a portable (Win, Linux, OS/X) GATT client library, prefereable with C++ binding? The only one, that I've found so far is Qt. What do you use...
I have been using nRF8001 equipped Arduinos for a few years now with great success. I exclusively use apple software on the other end. I have a new application that will required...
i want use a 9 axis IMU sensor (3 axis accelerometer,3 axis gyroscope and 3 axis magnetometer) in nrf51822 is it possible and how the transmission of values takes place.....
Hi,
I'm using the bootloader in nRF5_SDK V12.0 with nRF52832. I have some problems want to know:
How to make it run application first after I program softdevice...
I notice that the track which runs from P0.11 (E4) is connected to GND at pads C3 and C4. Is this intentional? If P0.11 is required for GPIO usage, is it necessary to go to...
I am trying to update my project to SDK 12.2 which was released this week and I am getting a ton of compiler errors with the FreeRTOS source files. For example, I try an compile...
I'm a begineer in nRF52DK and S132.
I am trying to make an application code to enable link layer control procedures at any time in a connection state with the nRF52DK and...
hello everyone，
Which APP demon is the most stable APP？
I use nrf-master APP to test the blue device，it can connect very well。but when I use uart-app ， it can't connect...
I notice that if Make virtually any of the SDK12 armgcc examples that I get a warning that 2 include folders do not exist
e.g.
../../config/ble_app_hrs_pca10028_s130...
