Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...
Hello!
1)There is problem with nrf_ble_uart. On sdk 4.4 work well, but sdk 5.1 the same code is not working.
What changes were made in the sdk or maybe there is a ready...
Hi I have built a custom NRF8001 board and I'm debugging a problem.
The main microcontroller works fine (atmega32u4) but the RDYN line never goes low to start the setup...
I am starting development on the nRF51422. I noticed that for the non-ANT sample code (blinky and UART), a gcc makefile and windows batch files are provided for compilation...
Hi,
Does the heart rate demo in SDK v4.4.0 work with SD v6.0.0? I'm using the QFAAC0 revision of the NRF51822. The demo works fine with SD v5.2.0. Is there anything special...
So far I haven't run across any code examples that will switch the BLE (S110) stack in and out. I'm looking to test enabling and disabling of the softdevice to see how that...
I'm reading AD-converter data usin nRF51822 SPI-Master. BLE-stack is active so I can't use
interrupts with SPI. I get data every 2 ms. Sometimes Events are delayed so long...
Hi,
We would like to implement a scenario that need two BLE devices,
One is Peripheral that able to broadcast and connectable,
another one is Central that able to scanning...
Hi,
I'm using nRF51 SDK v 5.1.0 with SoftDevice v6.0.0 on nRF51822.
I'm using the pstorage SDK module for flash operations.
I've found an issue with this module,...
Hi
In the product specification the S120 softdevice it is mentioned, that the S120 will support central and broadcaster role at the same time. This is exactly what we need...
I've cut the BLE proximity app example code back to doing nothing more than this:
int main(void)
{
uint32_t err_code;
leds_init();
for (;;)
{
power_manage...
