When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I was reading about RF design and some articles say that if the transmission line is short enough, you may not consider impedance-control as the effect is not visible...
Hi all,
For my project I power the nRF51 DK from a supercap using an external LDO(3.3V) connected to VDD. This way I can keep the board powered using the supercap. I also...
Hi
I'm using PCA10028. it has nrf51422 with softdevice s110. For getting printf in console I'm using 'app_uart.c with FIFO' and 'retarget.c'. When i try to print something...
I'm developing a project base on ble_app_uart now.
But I find out that the current value of ble_app_uart is > 1mA.
I want to reduce the average value to about 10uA when...
Hey,
I have a requirement to launch google play store/ installed app in an Android/ IOS mobile upon pairing of the nrf51822 with a mobile.
So can anyone help me out...
Hi,
i'm testing softdevice s130 central/peripheral example. I modefied the uuid of device to which my nrf58122 should connect, but i get error 0x05 (Device not found) everytime...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I use sdk 5.2.0 now. And my keil version is uvision4(4.70.0.0). My PC is windows XP.
Now I want to migrate to nRF51_SDK_8.1.0_b6ed55f_packs. But when I run "install.bat"...
I am getting notification of connections established between two boards in hyper terminal. Now i want to send this notification on web server as it is part of my project....
When I'm trying to connect to the new nrf51 dk kit with nrfgo studio, and at the same time have another j-link based dev-kit connected to the PC, the studio hangs while trying...
I started with the ble_app_template example. This example uses the Button event and notifies it. I modified the project to send some other data as notification, instead of...
Hi,
I am using the following calculations to calculate the power consumption for the chip:
Formulae to calculate battery power consumption:
Current consumption is...
Hi NORDIC
I neen to implement a function that multilink central (S120) can receive information from multilink peripheral . I do not know how to implement it in software...
Ok so I've followed the instructions to make my dev dongle (pca10000) a sniffer in "nRF Sniffer User Guide v1.2". Now I want to use it the way I used to use it in MCP.
...
