I'm currently working on a project using the nRF52833 with nRF5 SDK 17.1.0 and SoftDevice S140 v7.2.0 , aiming to run BLE (Peripheral role) and Qorvo DW3000-based UWB communication...
In NRF5 SDK17.1, I disabled the Bluetooth broadcast channels 38 and 39 by configuring channel_mask. However, when I measured the broadcast current waveform, I found that there...
Hello,
We are in the final stages of development with a board that combines the nRF5340 with the nRF7002. This board also requires native USB support and we are routing...
We are using the nRF5340 with Zephyr OS v3.6.99-100befc70c74 and nRF Connect SDK v2.7.0-5cb85570ca43. We have the following questions:
Is our understanding correct that...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
Hi Support team:
I am new for using the Nordic Design kit of nRF54L15-DK.
And I would like to use the app "Direct Test Mode" v2.4.2 built-in the "nRF Connect for Desktop...
Hi!
We have several products which use SoftDevice S110, some of them are already in production and are listed as Bluetooth Qualified, some of them we are preparing for production...
I've a custom board that uses a nrf52832 and Li-SOCl2 battery (3.7V). We've programmed several boards with our firmware and kept then with BLE advertisings every 300ms. A...
I am trying to develop a simple SPI master for a custom nRF52832 uC, but I can't find anny sort of sample codes that don't use Soft devices for this task. I need the code...
hi guys. I am currently using nrf52832 MDBT42Q Series from Raytac. I would like to know that how can I flash the softdevice and my application into the nrf52. My NRFgo unable...
I am currently doing some stress testing to ensure that I am correctly removing peers when the peer manager storage is full.
In this regard, my device is acting as a peripheral...
Hi,
I am developing application using nRF52832, s132, sdk13.2 which is collect sensor data and sent it to server. I have sent data to server using nRf52832 and interface...
Hello,
I'm trying to load BLE UART example on a custom module with nrf52832. I'm using SDK 14.
On the EVK it runs successfully, and I have the following addresses map...
Hello!
I'm trying to perform DFU over BLE using a NRF52 devkit. I'm getting the following error preceded by lots of "Invalid advertising data type" logs:
Traceback (most...
[SOLVED] turn off logging through UART.
Hello
I'm experiencing a strange issue where my device sends a beacon under DEBUG, but does not under RUN.
Due to that I tried...
Hi NordicSemiconductor Community,
I have a problem with the SEGGER Embedded Studio IDE, i want to build my project but i have the following error :
can't open 'C:/Users...
Hello,
I am trying to send out a notification and getting this error code 13313 (in decimal, 0x3401 in hex). Which eventually leads to BLE_ERROR_GATTS_SYS_ATTR_MISSING...
I developing applciation based on nrf51822, sdk11. I have read several posts about using app_timer_cnt_get() and get only 0 value. As far as I understand, this is because...
i want to connect my nfr51822 device to only one phone( that means which phone was connected first). For this purpose i enable whitelists but i create whitelists nothing has...
