Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi
We exposed NFC Type 2 functionality in our nrf52 a while back. Then the NFC SDK got refactored and I had to refactor my code to suite.
Now I am trying to enhance my...
Hi,
We would like to protect our product from people accessing the device via J-Link. We build our application with FreeRTOS. Can we follow this to set it before I start...
Hello,
I want to change data channels after provisioning, I follow devzone.nordicsemi.com/.../ here.
To set,
memset(&new_opt_config, 0, sizeof(new_opt_config));...
Hello Sir,
I am using nRf52832 s132, i want to write program which is automatically ON from sleep mode and after few second it will go system off mode for 1hr.
How i can...
Hi,..My device generated PWM square waves. I can program the frequencies and delays that is desired. but how to modulate current as per our requirement. I need the current...
Hello, I have recently bought a couple of boards from eBay that come with the nRF58232:
https://www.ebay.com/itm/Wireless-Bluetooth-Transceiver-Module-NRF52832-Development...
hi guys,
Can you please tell me what is happening when a smart phone trying to connect to nrf51822? Any event I could use? Would the connecting process has any impact on...
Hi,
I've just got my hands on this amazing little thing call Thingy 52. I have played around with the default app but now I'm struggling with flashing a custom firmware...
Hello,
I am trying to setup two Thingys with my node-red system and i have ran into some problems. The thingys respond to normal command line tools like gatttool, btmgmt...
Hi All,
I am new to Nordic microcontrollers. I am using keil uvision MDK lite version. After I have uploaded a source code and when i am trying to compile. I am getting...
Hello,
I am starting a new thread concerning the two messages that I have posted about generating a 4MHz clock on nRF52832. I am using the nRF5_SDK_14.2.0_17b948a SDK. ...
Hi,
if I correct understood DFU process first of all it need to send "Init packet" and after that it need to send FW image. And for that reason in DFU packages is 3 files...
Sir, i am looking to design customized board using nrf52832, i have pca10040 borad as well. i am looking for eagle library of antenna used in pca10040 (i.e nrR52DK).
if...
Hi, I'm trying to program a nRF52-DK, with a workong firmware, and a board that was working, but I can't manage to flash the DK.
With a make flash_softdevice:
Flashing...
I am working on nrf52832 BLE. I have used soft device s132. Antenna device is as per the reference design of NRF52832 and have used 32MHZ crystal for HFXO oscillator. but...
