Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I would like to know if there is any documentation that speaks of security for push notifications. For example, that talk about security when using a nRF52 device as a beacon...
Hi,
Is it possible to make infinite GATT connection ? I set auto connect in android central app and my program in nrf51DK works. But only 4 hours.
Hardfault is almost...
When I try to build example in SDK 12.3.0, I always get the hex file for nRF51422 target, how should I change the target to build the example for nRF51822?
I set the variables...
I would like to get the timesync example running on the Sparkfun nRF52832 Breakout board .
I can currently download it to the nRF52832 DK using Segger Studio (after making...
Hi all,
I am beginner in Java, I have experince just with assembler and C. I did only one app before in java, with Laird libraries, because we have Laird boards using Nordic...
Hi. I've seen many questions here regarding BLE throughput, I've been trying to get something better than the 200 B/s I'm getting.
I am using a nrf52832 as a GATT server...
I tried to sniff Mesh Packets send with the Light Switch Example but I didn't get any.
For sniffing I use the nrfsniffer v2 with the nrf dongle and for the Light Switch...
I'm trying to get nRF UART logging to work and have included all the nRF_Log libraries as per the blinky example (which works).
However, upon building, I'm getting
"nrf_fprintf...
I am currently using the NRF24l01+ but i want to know if I should be using a different product for my application. I am sending very small amount of information (such as hex...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I have a client device that normally is able to call ble_db_discovery_start and get the callback just fine and is able to complete the db discovery process. However sometimes...
I try to use SPI with easy DMA, in page 279 in the datasheet says: " An SPI master transaction consists of a sequence started by the START task followed by a number of events...
I have an issue with waking up SPI communication after sleep.
Befor I go to sleep I'm disabling SPI communication:
NRF_SPI0->ENABLE = 0;
NRF_SPI1->ENABLE = 0;
...
